BLACK OUT TAPE(for Rear Door) INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. REPAIR INSTRUCTION

   Click here

2. INSTALL NO. 3 BLACK OUT TAPE LH

   Tech Tips

   When installing the No. 3 black out tape LH, heat the front door panel and No. 3 black out tape LH using a heat light.

   Standard
   Item Temperature Front Door Panel 40 to 60°C (104 to 140°F) No. 3 Black Out Tape LH 20 to 30°C (68 to 86°F)

   Note

   Do not heat the front door panel or No. 3 black out tape LH excessively.

   
   

   1. Refer to the illustration to position a new No. 3 black out tape LH.

      

      *a	1.5 mm (0.0591 in.)	*b	1.0 mm (0.0394 in.)
      *c	5.0 mm (0.197 in.)	*d	Edge of Curved Surface

   2. Remove the release paper from the No. 3 black out tape LH.

3. INSTALL NO. 2 BLACK OUT TAPE LH

   Tech Tips

   When installing the No. 2 black out tape LH, heat the front door panel and No. 2 black out tape LH using a heat light.

   Standard
   Item Temperature Front Door Panel 40 to 60°C (104 to 140°F) No. 2 Black Out Tape LH 20 to 30°C (68 to 86°F)

   Note

   Do not heat the front door panel or No. 2 black out tape LH excessively.

   
   

   1. Refer to the illustration to position a new No. 2 black out tape LH.

      

      *a	1.5 mm (0.0591 in.)	*b	1.0 mm (0.0394 in.)
      *c	Edge of Curved Surface	-	-

   2. Remove the release paper from the No. 2 black out tape LH.

4. INSTALL NO. 1 BLACK OUT TAPE LH

   Tech Tips

   When installing the No. 1 black out tape LH, heat the front door panel and No. 1 black out tape LH using a heat light.

   Standard
   Item Temperature Front Door Panel 40 to 60°C (104 to 140°F) No. 1 Black Out Tape LH 20 to 30°C (68 to 86°F)

   Note

   Do not heat the front door panel or No. 1 black out tape LH excessively.

   
   

   1. Refer to the illustration to position a new No. 1 black out tape LH.

      

      *a	1.0 mm (0.0394 in.)	*b	5.0 mm (0.197 in.)
      *c	Edge of Curved Surface	-	-

   2. Remove the release paper from the No. 1 black out tape LH.

5. INSTALL REAR DOOR REAR WINDOW FRAME MOULDING LH

   Click here

6. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING LH

   Click here

7. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH

   Click here

8. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

   Click here

9. INSTALL REAR DOOR FRAME GARNISH LH

   Click here

10. INSTALL REAR DOOR WEATHERSTRIP LH

    Click here

11. CONNECT REAR DOOR CHECK ASSEMBLY LH

    
    

    1. Apply MP grease to the sliding area of the rear door check assembly LH.

    2. When reusing a bolt:

       
       

       1. Clean the threads of the bolt with non-residue solvent.

       2. Apply adhesive to the threads of the bolt.

          Adhesive
          Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

    3. 

       Connect the rear door check assembly LH with the bolt.

       Torque:

       27 N*m  { 275 kgf*cm, 20 ft.*lbf }

12. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Click here

13. INSTALL REAR DOOR REAR GUIDE SEAL LH

    Click here

14. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

    Click here

15. INSTALL REAR DOOR GLASS RUN LH

    Click here

16. INSTALL REAR DOOR SERVICE HOLE COVER LH

    Click here

17. INSTALL REAR DOOR ARMREST SET BRACKET LH

    Click here

18. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

    Click here

19. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    Click here

20. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    Click here

21. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH

    Click here

22. INSTALL REAR DOOR TRIM COVER LH

    Click here

23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

24. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

25. CHECK POWER WINDOW CONTROL SYSTEM

    Click here