FOG LIGHT ASSEMBLY REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL FOG LIGHT UNIT LH

    Note


    • Perform work using rubber gloves.

    • Do not touch the fog light unit LH with bare hands.

    • If dirty, lightly wipe with a soft cloth.


    1. Set the fog light unit LH to the aiming screw.

      Note

      Do not touch the printed wire board.

    2. A01HJRZ

      While holding the fog light unit LH with one hand so that it does not fall over, tighten the aiming screw same number of rotations recorded when removing it to connect the aiming screw.

      Note

      Do not touch the printed wire board.

    3. A01HJB9

      Attach the 2 pivot collars.

    4. Tighten the aiming screw 20 rotations.

    5. Connect the connector.

  2. INSTALL FOG LIGHT GASKET


    1. B005B37C01
      B0057KY Area to Clean

      Clean the fog light gasket installation groove.

    2. A01HI6H

      Prepare 2 screwdrivers, fold a piece of peeling paper over the tip of each screwdriver and fix the pieces of peeling paper in place with tape.

      Tech Tips

      Use the peeling paper that is supplied with the fog light gasket.

    3. Using scissors, cut the end of a new fog light gasket at a diagonal (45°).

    4. B0057KRC01
      B0057KY Starting Point

      Starting at the lower side of the fog light lens LH claw attaching point, set the fog light gasket into the straight groove counterclockwise until it meets the corner groove.

      Note

      Lightly set the gasket in place without pulling.

    5. Using 2 screwdrivers with their tips wrapped with peeling paper, push the fog light gasket into the bottom of the groove.

    6. B005939C01
      B0059IK Corner Groove

      Set the fog light gasket into the corner groove and using 2 screwdrivers with their tips wrapped with peeling paper, push the gasket into the bottom of the groove.

      Note


      • Lightly set the gasket in place without pulling.

      • If the fog light gasket is set while pulled, the gasket will be pushed up at the corner groove.

    7. B005ADLC01
      B0057RX Push In
      B0057KY Peeling Paper

      Repeat the following order while working in a circle back to the starting point: 1) Set fog light gasket into straight groove, 2) push into bottom of groove, 3) set into the corner groove and 4) push into bottom of groove.

    8. Using scissors, cut the fog gasket at a 45° angle at the starting point so that the gasket overlaps itself 10 mm (0.3937 in.) or more and set the gasket in place.

    9. B00587UC01
      *a 10 mm (0.3937 in.)
      B0059IK Corner Groove

      Check the installation condition of the fog light gasket.

      OK
      Gasket not pushed up or protruding.
      No gap where gasket overlaps.

      Note

      Check the corners carefully since the gasket can easily become pushed up in those areas.

  3. INSTALL FOG LIGHT LENS LH

    Note


    • Perform work using rubber gloves.

    • Do not touch the fog light lens LH with bare hands.

    • If dirty, lightly wipe with a soft cloth.


    1. Clean the fog light gasket contact surface.

    2. Set the fog light lens LH in place.

    3. B005B3BC01
      *a Base Point

      Attach the 2 claws.

      Tech Tips

      Attach the claw at the base point first.

    4. Using a T20H "TORX" screwdriver, install the screw.

    5. Install the 3 screws.

    6. Check that the fog light gasket installation condition.

      OK
      Gasket contacts fog light lens LH and does not protrude out.