STOP AND START SYSTEM REGISTRATION

PROCEDURE


  1. ECU EXCHANGE


    1. for 8AR-FTS:

      Note

      After replacing the engine stop and start ECU, upload the number of starter operations to the new engine stop and start ECU using the GTS.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.


        Powertrain > Stop and Start > Utility
        Tester Display
        ECU Exchange

      5. According to the GTS display, download the previous status (the number of starter operations) from the old engine stop and start ECU to the GTS.

      6. Replace the engine stop and start ECU.

        Click here

      7. According to the GTS display, upload the previous status (the number of starter operations) from the GTS to the new engine stop and start ECU.

    2. for 3ZR-FAE:

      Note

      When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the engine switch on (IG) and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Stop&Start Operating Permission (Discharged Oil Pump Air)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Powertrain / Stop and Start / Utility / ECU Exchange.


        Powertrain > Stop and Start > Utility
        Tester Display
        ECU Exchange

      5. According to the display on the GTS, download the previous status (the number of starter operations) from the old engine stop and start ECU to the GTS.

      6. Replace the engine stop and start ECU.

        Click here

      7. Turn the engine switch on (IG) and wait for 20 seconds.

      8. Enter the following menus: Powertrain / Stop and Start / Data List / Stop&Start Operating Permission (Discharged Oil Pump Air).

        Check that "OK" is displayed.


        Powertrain > Stop and Start > Data List
        Tester Display
        Stop&Start Operating Permission (Discharged Oil Pump Air)

      9. According to the display on the GTS, upload the previous status (the number of starter operations) from the GTS to the new engine stop and start ECU.

  2. CLEAR NUMBER OF STARTER OPERATIONS

    Note


    • After the starter assembly is replaced, be sure to clear the number of starter operations stored in the engine stop and start ECU.

    • When the starter assembly is replaced, "ST relay" and "ST NO. 2 relay" must be also replaced.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Utility / Starter Exchange.


      Powertrain > Stop and Start > Utility
      Tester Display
      Starter Exchange

  3. RESET AIR CONDITIONING INFORMATION

    Note

    After replacing the engine stop and start ECU or air conditioning amplifier assembly, initialization of the air conditioning information in the engine stop and start ECU is necessary.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Utility / Reset A/C Information.


      Powertrain > Stop and Start > Utility
      Tester Display
      Reset A/C Information

  4. LEARNING AIR CONDITIONING INFORMATION

    Tech Tips

    When initialization of the air conditioning information is complete, air conditioning information learning is automatically performed. If the learning cannot be performed properly, inspect the CAN communication system.

  5. CLEAR THE ZERO POINT CALIBRATION DATA

    Note


    • After replacing the engine stop and start ECU or airbag ECU assembly, perform deceleration sensor zero point clear and calibration.

    • Once the zero point is stored, it cannot be overwritten until the data is cleared. Be sure to perform zero point clear and calibration after replacing the airbag ECU assembly.


    1. Turn the engine switch off.

    2. Move the shift lever to P and apply the parking brake.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

      Tech Tips

      Do not start the engine.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Clear.


      Powertrain > Stop and Start > Utility
      Tester Display
      Deceleration Sensor Zero Point Clear

      Note

      When the deceleration sensor zero point is cleared, the system information stored in the engine stop and start ECU is also cleared. If the vehicle is driven for 5 seconds or more at 3 km/h (2 mph) or more in this condition, the engine stop and start ECU will store DTC P158954 and blink the stop and start cancel indicator light.

    7. Turn the engine switch off.

  6. PERFORM ZERO POINT CALIBRATION OF THE DECELERATION SENSOR

    Note

    Park the vehicle on a level surface (grade: +/-1%). Do not shake the vehicle or open/close any of the doors during zero point calibration. To avoid vibration caused by the engine idling, do not start the engine.


    1. Connect the GTS to the DLC3.

    2. Check that the shift lever is in P.

    3. Turn the engine switch on (IG).

      Tech Tips

      Do not start the engine.

    4. Check that the parking brake is applied and the brake warning light is illuminated.

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Stop and Start / Utility / Deceleration Sensor Zero Point Calibration.


      Powertrain > Stop and Start > Utility
      Tester Display
      Deceleration Sensor Zero Point Calibration

      Tech Tips

      If DTC P158954 is stored, the stop and start cancel indicator light will blink.

    7. While keeping the vehicle stationary, follow the prompts on the GTS screen. Check that "Complete" is displayed on the GTS screen.

      Note

      If zero point calibration fails, perform the registration procedure again from "CLEAR THE ZERO POINT CALIBRATION DATA".

  7. CLEAR THE INTEGRATED CURRENT VALUE

    Tech Tips

    After charging the battery or replace battery, perform the integrated current value initialization.

    If the Data List item "Integrated Current" indicates 0 or more, initialization is not necessary.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Utility / Integrated Current Value Initialization.


      Powertrain > Stop and Start > Utility
      Tester Display
      Integrated Current Value Initialization

  8. AIR BLEED OIL PUMP ASSEMBLY WITH MOTOR

    Note

    for 8AR-FTS:

    Bleed the oil pump assembly with motor (automatic transaxle assembly) after replace the automatic transaxle assembly or replacing the automatic transaxle fluid.

    for 3ZR-FAE:

    Bleed the oil pump assembly with motor (continuously variable transaxle assembly) after removing and installing the continuously variable transaxle assembly or replacing the CVT fluid.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

      Tech Tips

      Do not start the engine.

    3. Turn the GTS on.

    4. Perform the " Oil Pump" Active Test for 10 seconds or more.

      Enter the following menus: Powertrain / Stop and Start / Active Test / Oil Pump.


      Powertrain > Stop and Start > Active Test
      Tester Display
      Oil Pump

  9. SWITCH BATTERY TYPE


    1. Check whether the battery is specified or not specified.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

      Tech Tips

      Do not start the engine.

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Stop and Start / Data List / Battery Type.

      Tech Tips

      Check the battery type (Specified/Other) stored by the ECU.


      Powertrain > Stop and Start > Data List
      Tester Display
      Battery Type

    6. If the battery installed does not match the battery stored by the ECM, switch to the battery type for the installed battery.


      1. for 8AR-FTS:

        Enter the following menus: Powertrain / Engine / Utility / Switch Battery Type.


        Powertrain > Engine > Utility
        Tester Display
        Switch Battery Type

        for 3ZR-FAE:

        Enter the following menus: Powertrain / Engine and ECT / Utility / Switch Battery Type.


        Powertrain > Engine and ECT > Utility
        Tester Display
        Switch Battery Type