STOP AND START SYSTEM, Diagnostic DTC:B22C0

DTC Code DTC Name
B22C0 BBC Overcurrent

DESCRIPTION

A backup boost converter is built into the engine stop and start ECU.

The backup boost converter helps maintain battery voltage to prevent various functions from failing if power source voltage supplied from the backup boost converter drops due to the high electrical load when the engine is restarted by stop and start control.

The backup boost converter helps maintain the power source voltage if the battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.

Tech Tips

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset*1 when the engine switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the engine switch is turned on (IG).

*1: A semiconductor fuse self resets according to electric signal.

The backup boost converter supplies power to:


  • Vehicle stability control system

  • Power steering system

  • Dynamic radar cruise control system

  • Inner rear view mirror assembly (w/ EC Mirror)

  • Lane departure alert system

  • Air conditioning system

  • CAN communication system (Network gateway ECU)

  • Panoramic view monitor system

  • Blind spot monitor system

  • Meter / Gauge system (Headup display)

  • Remote operation controller assembly

  • Telematics System

  • Tire pressure warning system

  • Entry and start system (w/ Entry and Start System)

  • Push-button start (w/o Entry and Start System)

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
B22C0 BBC Overcurrent

The following condition continues for 1 second or more (1 trip detection logic):


  • Overcurrent is detected at the BO1 and IGO1 terminals in the engine stop and start ECU

  • Engine stop and start ECU

  • Wire harness or connector

  • Spiral with sensor cable sub-assembly

  • Skid control ECU (Brake actuator assembly)

  • Power steering ECU assembly

  • Parking assist ECU (w/ Panoramic View Monitor System)

  • Inner rear view mirror assembly (w/ EC Mirror)

  • Network gateway ECU

  • Air conditioning control assembly

  • Tire pressure warning ECU and receiver (Tire Pressure Warning ECU and Receiver (for LH Side))

  • Tire pressure warning ECU and receiver (Door control and tire pressure monitoring system receiver assembly) (Tire Pressure Warning ECU and Receiver (for RH Side))

  • Telematics transceiver (w/ Telematics Transceiver)

  • Remote operation controller assembly

  • Combination meter mirror ECU (w/ Headup Display)

  • Lane departure warning camera (w/ Lane Departure Alert System)

  • Blind spot monitor sensor LH (w/ Blind Spot Monitor System)

  • Blind spot monitor sensor RH (w/ Blind Spot Monitor System)

  • Driving support ECU assembly (w/ Dynamic Radar Cruise Control System)

  • Millimeter wave radar sensor assembly (w/ Dynamic Radar Cruise Control System)

 Blinks DTC stored

CONFIRMATION DRIVING PATTERN

Tech Tips

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click here


  1. CONFIRMATION AFTER TROUBLESHOOTING

    Tech Tips


    • If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

    • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Clear the DTCs.

      Click here


      Powertrain > Stop and Start > Clear DTCs

    4. Start the engine and warm it up.

    5. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    6. Depress the brake pedal and stop the vehicle.

    7. Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)

    8. Release the brake pedal with the shift lever in D to start the engine.

      Tech Tips

      If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.

    9. Check that DTCs are not output.

      Click here


      Powertrain > Stop and Start > Trouble Codes

  2. STOP AND START SYSTEM OPERATION CHECK

    Tech Tips

    If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    4. Depress the brake pedal and stop the vehicle.

    5. Allow the engine to stop by stop and start control. (Keep the shift lever in D.)

    6. Release the brake pedal with the shift lever in D to start the engine.

WIRING DIAGRAM

A01OF0CE02
A01OEGVE01
A01OE2JE01

CAUTION / NOTICE / HINT

Note


  • for 8AR-FTS:

    Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

    Click here

  • for 3ZR-FAE:

    When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the engine switch on (IG) and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

    Click here

  • If electrical load from additional devices installed to the vehicle (aftermarket audio system, etc.) is applied to the BO1 or IGO1 terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate.

    If the fuse function of the backup boost converter operates, any systems connected to the BO1 or IGO1 terminal in the engine stop and start ECU will not operate.

  • If DTCs P1539 and B22C0 are output simultaneously, troubleshoot for DTC P1539 (oil pump malfunction) first, as a malfunction which causes DTC P1539 to be stored may also cause DTC B22C0 (BBC boost converter over-current) to be stored.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Stop and Start > Trouble Codes
      Result
      Result Proceed to
      DTC B22C0 is output A
      DTC P1539 and B22C0 are output B

    B

    GO TO DTC P1539 Click here

    A

  2. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC NO. 1 FUSE)


    1. Disconnect the A37 engine stop and start ECU connector.

    2. Remove the BBC NO. 1 fuse from No. 1 engine room relay block and junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A37-7 (BIN) - BBC NO. 1 fuse terminal 2 Always Below 1 Ω
      A37-7 (BIN) - Body ground Always 10 kΩ or higher
      BBC NO. 1 fuse terminal 2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)


    1. Disconnect the I57 engine stop and start ECU connector.

    2. Disconnect the A36 skid control ECU (brake actuator assembly) connector.

    3. Disconnect the n2 power steering ECU assembly connector. (w/ Power Tilt and Power Telescopic)

    4. Disconnect the n3 power steering ECU assembly connector. (w/o Power Tilt and Power Telescopic)

    5. Disconnect the I6 spiral with sensor cable sub-assembly connector.

    6. Disconnect the I19 driving support ECU assembly connector. (w/ Dynamic Radar Cruise Control System)

    7. Disconnect the T5 inner rear view mirror connector. (w/ EC Mirror)

    8. Disconnect the A21 millimeter wave radar sensor assembly connector. (w/ Dynamic Radar Cruise Control System)

    9. Disconnect the T10 Lane departure warning camera connector. (w/ Lane Departure Alert System)

    10. Disconnect the I67 network gateway ECU connector.

    11. Disconnect the I13 air conditioning control assembly connector.

    12. Disconnect the P19 parking assist ECU connector. (w/ Panoramic View Monitor System)

    13. Disconnect the Q46 tire pressure warning ECU and receiver connector. (Tire Pressure Warning ECU and Receiver (for LH Side))

    14. Disconnect the P11 tire pressure warning ECU and receiver (door control and tire pressure monitoring system receiver assembly) connector. (Tire Pressure Warning ECU and Receiver (for RH Side))

    15. Disconnect the X1 blind spot monitor sensor RH connector. (w/ Blind Spot Monitor System)

    16. Disconnect the V1 blind spot monitor sensor LH connector. (w/ Blind Spot Monitor System)

    17. Disconnect the I40 telematics transceiver connector. (w/ Telematics Transceiver)

    18. Disconnect the J5 combination meter mirror ECU connector. (w/ Headup Display)

    19. Disconnect the I71 remote operation controller assembly connector. (w/ Navigation System)

    20. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I57-2 (BO1) - P19-2 (+B)*1 Always Below 1 Ω
      I57-2 (BO1) - I40-1 (+B)*11 Always Below 1 Ω
      I57-2 (BO1) - I71-1 (+B)*8 Always Below 1 Ω
      I57-12 (IGO1) - A36-12 (IG1) Always Below 1 Ω
      I57-12 (IGO1) - n2-1 (IG)*9 Always Below 1 Ω
      I57-12 (IGO1) - n3-1 (IG)*10 Always Below 1 Ω
      I57-12 (IGO1) - I19-30 (B)*2 Always Below 1 Ω
      I57-12 (IGO1) - I6-4 (IG1) Always Below 1 Ω
      I57-12 (IGO1) - T5-1 (IG)*3 Always Below 1 Ω
      I57-12 (IGO1) - T10-7 (IGB)*4 Always Below 1 Ω
      I57-12 (IGO1) - A21-5 (IGB)*2 Always Below 1 Ω
      I57-12 (IGO1) - I67-10 (IG1) Always Below 1 Ω
      I57-12 (IGO1) - I13-8 (IG+) Always Below 1 Ω
      I57-12 (IGO1) - Q46-1 (IG)*5 Always Below 1 Ω
      I57-12 (IGO1) - P11-1 (IG)*6 Always Below 1 Ω
      I57-12 (IGO1) - X1-5 (BRB)*7 Always Below 1 Ω
      I57-12 (IGO1) - V1-5 (BLB)*7 Always Below 1 Ω
      I57-12 (IGO1) - I40-7 (IG2)*11 Always Below 1 Ω
      I57-12 (IGO1) - J5-1 (IG)*12 Always Below 1 Ω
      I57-12 (IGO1) - P19-6 (IG)*1 Always Below 1 Ω
      I57-2 (BO1) - Body ground Always 10 kΩ or higher
      I57-12 (IGO1) - Body ground Always 10 kΩ or higher

      • *1: w/ Panoramic View Monitor System

      • *2: w/ Dynamic Radar Cruise Control System

      • *3: w/ EC Mirror

      • *4: w/ Lane Departure Alert System

      • *5: Tire Pressure Warning ECU and Receiver (for LH Side)

      • *6: Tire Pressure Warning ECU and Receiver (for RH Side)

      • *7: w/ Blind Spot Monitor System

      • *8: w/ Navigation System

      • *9: w/ Power Tilt and Power Telescopic

      • *10: w/o Power Tilt and Power Telescopic

      • *11: w/ Telematics Transceiver

      • *12: w/ Headup Display

      Result
      Proceed to
      OK
      NG

      Tech Tips

      The installation location of the tire pressure warning ECU and receiver differs depending on the specification. Refer to the following link for the installation location information.

      Click here


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK ENGINE STOP AND START ECU


    1. Disconnect the A37, A38 and I57 engine stop and start ECU connectors.

      A01XOKUC03
      *a

      Component without harness connected

      (Engine Stop and Start ECU)

      		 - -

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I57-2 (BO1) - A37-8 (GND) Always 10 kΩ or higher
      I57-12 (IGO1) - A37-8 (GND) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ENGINE STOP AND START ECU Click here

    OK

  5. CHECK VEHICLE CONDITION (BO1, IGO1 CIRCUIT)


    1. Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the BO1 or IGO1 terminal circuit of the engine stop and start ECU.

      Result
      Result Proceed to
      Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. A
      Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. B

    A

    TROUBLESHOOT ECUS CONNECTED TO TERMINALS BO1 AND IGO1

    B

    END (REMOVE ADDITIONAL DEVICE)