OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will cause removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

  • For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap sub-assembly.

    2. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    3. Clean and install a new gasket and the oil pan drain plug.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  2. REMOVE OIL FILTER


    1. for Oil Filter Sub-assembly Type:


      1. A01XO3IN01

        Using SST, remove the oil filter sub-assembly.

        SST
        09228-06501

    2. for Oil Filter Element Kit Type:


      1. A01XOEAC06
        *1 Oil Filter Bracket Clip
        *a Oil Filter Cap Assembly Rib

        Using SST, loosen the oil filter cap assembly 4 revolutions, align the oil filter cap assembly ribs vertically, and drain the remaining engine oil in the oil filter cap assembly.

        SST
        09228-06501

        Note

        Do not remove the oil filter bracket clip when removing the oil filter cap assembly.

        Tech Tips

        Set a container below the oil filter cap assembly before loosening the oil filter cap assembly.

      2. Remove the oil filter cap assembly.

      3. A01XOLHC04
        *1 Oil Filter Element
        *2 O-Ring

        Remove the oil filter element and O-ring from the oil filter cap assembly.

        Note

        Be sure to remove the O-ring (for the oil filter cap assembly) by hand, without using any tools, to prevent damage to the groove for the O-ring on the oil filter cap assembly.

  3. INSTALL OIL FILTER


    1. for Oil Filter Sub-assembly Type:


      1. Check and clean the oil filter sub-assembly installation surface.

      2. Apply clean engine oil to the gasket of a new oil filter sub-assembly.

      3. Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.

      4. A01XNDBN01

        Using SST, tighten the oil filter sub-assembly.

        SST
        09228-06501

          Depending on the work space available, choose from the following:

        • If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

        Torque:
        17.5 N*m  { 178 kgf*cm, 13 ft.*lbf }

        • If not enough space is available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or use a common wrench.

    2. for Oil Filter Element Kit Type:


      1. Clean the inside of the oil filter cap assembly, its threads and O-ring groove.

      2. A01XPFVC26
        *a CORRECT
        *b INCORRECT
        B0058UH O-Ring

        Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.

        Note


        • Be sure to install the O-ring in the proper location, otherwise oil may leak.

        • Do not twist the O-ring.

      3. Set a new oil filter element in the oil filter cap assembly.

      4. Remove any dirt or foreign matter from the installation surface and inside of the engine.

      5. A01XNC4

        Reapply a small amount of engine oil to the O-ring of the oil filter cap assembly. Align the oil filter cap assembly with the oil filter bracket sub-assembly so that the cutout portion of the oil filter cap assembly threads is in a position 90° from the groove in the oil filter bracket sub-assembly, and then temporarily install the oil filter cap assembly.

        Note

        Make sure that the O-ring does not get caught between the parts.

      6. A01XOLJC11
        *1 Oil Filter Cap Assembly
        *2 O-Ring
        *3 Oil Filter Bracket Sub-assembly
        *a No Gap

        Using SST, tighten the oil filter cap assembly.

        SST
        09228-06501
        Torque:
        25 N*m  { 255 kgf*cm, 18 ft.*lbf }

        Note


        • After tightening the oil filter cap assembly, check for gaps between the installation surfaces.

        • Do not remove the oil filter bracket clip when installing the oil filter cap assembly.

        • Do not cross thread the oil filter cap assembly.

        • After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.

  4. ADD ENGINE OIL


    1. Add new engine oil and install the oil filler cap sub-assembly.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      0W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil 15W-40
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter change 3.9 liters (4.1 US qts, 3.4 Imp. qts)
      Drain and refill with oil filter change 4.2 liters (4.4 US qts, 3.7 Imp. qts)
      Dry fill 4.7 liters (5.0 US qts, 4.1 Imp. qts)

  5. INSPECT ENGINE OIL LEVEL

    Click here

  6. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.