OIL PUMP REMOVAL

CAUTION / NOTICE / HINT

Note

Do not remove the oil pump and oil pump relief valve from the timing chain cover assembly.

PROCEDURE


  1. REMOVE ENGINE AND TRANSAXLE

    Click here

  2. REMOVE IGNITION COIL ASSEMBLY

    Click here

  3. REMOVE NO. 2 WATER BY-PASS PIPE

    Click here

  4. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY (for High Pressure)

    Click here

  5. REMOVE FUEL PUMP ASSEMBLY (for High Pressure)

    Click here

  6. REMOVE NO. 2 PCV HOSE

    Click here

  7. DISCONNECT VACUUM TRANSMITTING HOSE ASSEMBLY

    Click here

  8. DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

    Click here

  9. DISCONNECT ENGINE WIRE

    Click here

  10. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

    Note

    w/ Canister Pump Module:

    Be sure not to disconnect the PCV hose or the No. 4 PCV hose from the cylinder head cover sub-assembly.


    1. Remove the 2 bolts and 2 camshaft position sensor from the cylinder head cover sub-assembly.

      B0058GFC01
      *A w/ Canister Pump Module *B w/o Canister Pump Module

    2. Remove the 19 bolts and cylinder head cover sub-assembly from the camshaft housing sub-assembly.

    3. B0057Y1C01
      *A w/ Canister Pump Module
      *B w/o Canister Pump Module
      *1 Cylinder Head Cover Gasket
      *2 No. 2 Cylinder Head Cover Gasket

      Remove the cylinder head cover gasket and No. 2 cylinder head cover gasket from the cylinder head cover sub-assembly.

    4. B0059RW

      Remove the 2 gaskets from the No . 1 camshaft bearing cap and No. 2 camshaft bearing cap.

  11. REMOVE FAN AND GENERATOR V BELT

    Click here

  12. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY

    Click here

  13. REMOVE IDLER PULLEY SUB-ASSEMBLY


    1. B005AY2

      Remove the bolt and idler pulley sub-assembly from the timing chain cover assembly.

  14. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    1. B005AF4

      Remove the 2 bolts and V-ribbed belt tensioner assembly from the timing chain cover assembly.

  15. REMOVE TRANSVERSE ENGINE MOUNTING BRACKET


    1. B005B90

      Remove the 4 bolts and transverse engine mounting bracket from the timing chain cover assembly.

  16. REMOVE CRANKSHAFT PULLEY ASSEMBLY

    Click here

  17. REMOVE CRANKSHAFT POSITION SENSOR

    Click here

  18. REMOVE TIMING CHAIN COVER ASSEMBLY


    1. B005908

      Remove the 2 nuts and 19 bolts from the timing chain cover assembly.

    2. Using a screwdriver wrapped in protective tape, remove the timing chain cover assembly by prying the points in the illustration.

      B005AY0C02
      *a Protective Tape - -

      Note

      Do not damage the contacting surfaces of the timing chain cover assembly, camshaft housing sub-assembly, cylinder head sub-assembly, stiffening crankcase assembly and cylinder block sub-assembly.

    3. B005AEB

      Remove the 2 oil pump gaskets and oil hole cover gasket from the stiffening crankcase assembly.

  19. REMOVE TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL


    1. B0058O4C02
      *a Protective Tape
      *b Wooden Block

      Using a screwdriver and wooden block, pay out the timing gear case or timing chain case oil seal.

      Note

      Do not damage the surface of the timing gear case or timing chain case oil seal press fit hole.