OIL PUMP COMPONENTS
ILLUSTRATION
| *A | for Type A | *B | for Type B |
| *1 | FUEL DELIVERY PIPE SUB-ASSEMBLY | *2 | FUEL INJECTOR ASSEMBLY |
| *3 | FUEL TUBE SUB-ASSEMBLY | *4 | INTAKE MANIFOLD |
| *5 | INTAKE MANIFOLD TO HEAD GASKET | *6 | PURGE VSV |
| *7 | THROTTLE BODY ASSEMBLY | *8 | VACUUM SENSOR ASSEMBLY |
| *9 | VACUUM SENSOR BRACKET | *10 | WIRE HARNESS CLAMP BRACKET |
| *11 | INTAKE MANIFOLD STAY | *12 | EFI FUEL PIPE CLAMP |
| *13 | INJECTOR VIBRATION INSULATOR | *14 | NO. 1 DELIVERY PIPE SPACER |
| *15 | ENGINE COVER JOINT | *16 | O-RING |
| *17 | GASKET | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Do not apply lubricants to the threads | - | - |
ILLUSTRATION
| *1 | EXHAUST MANIFOLD | *2 | MANIFOLD STAY |
| *3 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR | *4 | WIRE HARNESS CLAMP BRACKET |
| *5 | EXHAUST MANIFOLD TO HEAD GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | VACUUM PUMP ASSEMBLY | *2 | NO. 2 O-RING |
| *3 | NO. 3 O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Engine oil | - | - |
ILLUSTRATION
| *1 | ENGINE OIL LEVEL DIPSTICK GUIDE | *2 | IGNITION COIL ASSEMBLY |
| *3 | NO. 1 VACUUM PUMP BRACKET | *4 | NO. 3 WATER BY-PASS HOSE |
| *5 | NO. 2 PCV HOSE | *6 | V-RIBBED BELT TENSIONER ASSEMBLY |
| *7 | WATER BY-PASS HOSE | *8 | WATER INLET HOSE |
| *9 | ENGINE OIL LEVEL DIPSTICK | *10 | NO. 1 WATER BY-PASS PIPE |
| *11 | GASKET | *12 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CYLINDER HEAD COVER GASKET | *2 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *3 | SEAL WASHER | *4 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CRANKSHAFT PULLEY | *2 | NO. 1 CHAIN TENSIONER ASSEMBLY |
| *3 | OIL FILTER SUB-ASSEMBLY | *4 | OIL FILTER ELEMENT |
| *5 | THERMOSTAT | *6 | TIMING CHAIN COVER OIL SEAL |
| *7 | TIMING CHAIN COVER SUB-ASSEMBLY | *8 | TRANSVERSE ENGINE MOUNTING BRACKET STUD BOLT |
| *9 | WATER INLET | *10 | TRANSVERSE ENGINE MOUNTING BRACKET |
| *11 | OIL FILTER BRACKET SUB-ASSEMBLY | *12 | ENGINE WATER PUMP ASSEMBLY |
| *13 | SEAL WASHER | *14 | WATER PUMP GASKET |
| *15 | CRANKSHAFT PULLEY SET BOLT | *16 | BRACKET |
| *17 | O-RING | *18 | GASKET |
| *19 | OIL FILTER CAP ASSEMBLY | - | - |
| *a | for Oil Filter Sub-assembly Type | *b | for Oil Filter Element Kit Type |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease |  |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
| ★ | Precoated part | |
Do not apply lubricants to the threads |
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | CRANKSHAFT TIMING SPROCKET | *4 | NO. 1 CHAIN VIBRATION DAMPER |
| *5 | NO. 2 CHAIN SUB-ASSEMBLY | *6 | OIL PUMP DRIVE GEAR |
| *7 | OIL PUMP DRIVE SHAFT GEAR | *8 | CHAIN DAMPER SPRING |
| *9 | CHAIN TENSIONER PLATE | *10 | O-RING |
| *11 | OIL PUMP DRIVE SHAFT GEAR NUT | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | NO. 2 OIL PAN SUB-ASSEMBLY | *2 | OIL PUMP ASSEMBLY |
| *3 | OIL PAN DRAIN PLUG | *4 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | OIL PUMP COVER SUB-ASSEMBLY | *2 | OIL PUMP RELIEF VALVE |
| *3 | OIL PUMP ROTOR SET | *4 | OIL PUMP RELIEF VALVE SPRING |
| *5 | OIL PUMP RELIEF VALVE PLUG | *6 | OIL PUMP BODY |
| *7 | OIL PUMP DRIVEN ROTOR | *8 | OIL PUMP DRIVE ROTOR |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |