ENGINE UNIT COMPONENTS
ILLUSTRATION
| *A | for Type A | *B | for Type B |
| *1 | FUEL DELIVERY PIPE SUB-ASSEMBLY | *2 | FUEL INJECTOR ASSEMBLY |
| *3 | FUEL TUBE SUB-ASSEMBLY | *4 | INTAKE MANIFOLD |
| *5 | NO. 1 DELIVERY PIPE SPACER | *6 | PURGE VSV |
| *7 | THROTTLE BODY ASSEMBLY | *8 | VACUUM SENSOR ASSEMBLY |
| *9 | VACUUM SENSOR BRACKET | *10 | WIRE HARNESS CLAMP BRACKET |
| *11 | INTAKE MANIFOLD TO HEAD GASKET | *12 | EFI FUEL PIPE CLAMP |
| *13 | O-RING | *14 | INJECTOR VIBRATION INSULATOR |
| *15 | ENGINE COVER JOINT | *16 | GASKET |
| *17 | INTAKE MANIFOLD STAY | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Do not apply lubricants to the threads | - | - |
ILLUSTRATION
| *A | for 2WD | *B | for AWD |
| *1 | DRIVE SHAFT BEARING BRACKET | *2 | EXHAUST MANIFOLD |
| *3 | MANIFOLD STAY | *4 | NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
| *5 | EXHAUST MANIFOLD TO HEAD GASKET | *6 | WIRE HARNESS CLAMP BRACKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | VACUUM PUMP ASSEMBLY | *2 | NO. 2 O-RING |
| *3 | NO. 3 O-RING | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | ENGINE OIL LEVEL DIPSTICK GUIDE | *2 | HEATER WATER INLET HOSE |
| *3 | HEATER WATER OUTLET HOSE | *4 | IGNITION COIL ASSEMBLY |
| *5 | NO. 1 VACUUM PUMP BRACKET | *6 | NO. 1 WATER BY-PASS PIPE |
| *7 | NO. 2 GENERATOR BRACKET | *8 | NO. 2 PCV HOSE |
| *9 | NO. 3 WATER BY-PASS HOSE | *10 | NO. 3 WATER BY-PASS PIPE |
| *11 | STUD BOLT | *12 | ENGINE OIL TEMPERATURE SENSOR |
| *13 | THERMOSTAT | *14 | V-RIBBED BELT TENSIONER ASSEMBLY |
| *15 | WATER BY-PASS HOSE | *16 | WATER INLET |
| *17 | WATER INLET HOSE | *18 | O-RING |
| *19 | ENGINE OIL LEVEL DIPSTICK | *20 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT POSITION SENSOR | *2 | CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
| *3 | CYLINDER HEAD COVER GASKET | *4 | CYLINDER HEAD COVER SUB-ASSEMBLY |
| *5 | ENGINE COVER JOINT | *6 | TRANSVERSE ENGINE MOUNTING BRACKET STUD BOLT |
| *7 | OIL FILLER CAP GASKET | *8 | OIL FILLER CAP SUB-ASSEMBLY |
| *9 | SPARK PLUG | *10 | SPARK PLUG TUBE GASKET |
| *11 | O-RING | *12 | BRACKET |
| *13 | GASKET | *14 | SEAL WASHER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CRANKSHAFT PULLEY | *2 | ENGINE OIL PRESSURE SWITCH ASSEMBLY |
| *3 | NO. 1 CHAIN TENSIONER ASSEMBLY | *4 | OIL FILTER SUB-ASSEMBLY |
| *5 | STUD BOLT | *6 | TIMING CHAIN COVER OIL SEAL |
| *7 | TIMING CHAIN COVER SUB-ASSEMBLY | *8 | UNION |
| *9 | WATER INLET HOUSING | *10 | BRACKET |
| *11 | GASKET | *12 | OIL FILTER BRACKET |
| *13 | TRANSVERSE ENGINE MOUNTING BRACKET | *14 | O-RING |
| *15 | SEAL WASHER | *16 | ENGINE WATER PUMP ASSEMBLY |
| *a | for Oil Filter Sub-assembly Type | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
MP grease |  |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
| ★ | Precoated part | |
Do not apply lubricants to the threads |
ILLUSTRATION
| *1 | CRANKSHAFT PULLEY | *2 | ENGINE OIL PRESSURE SWITCH ASSEMBLY |
| *3 | NO. 1 CHAIN TENSIONER ASSEMBLY | *4 | OIL FILTER ELEMENT |
| *5 | STUD BOLT | *6 | TIMING CHAIN COVER OIL SEAL |
| *7 | TIMING CHAIN COVER SUB-ASSEMBLY | *8 | WATER INLET HOUSING |
| *9 | TRANSVERSE ENGINE MOUNTING BRACKET | *10 | BRACKET |
| *11 | GASKET | *12 | OIL FILTER BRACKET |
| *13 | OIL FILTER CAP ASSEMBLY | *14 | O-RING |
| *15 | SEAL WASHER | *16 | ENGINE WATER PUMP ASSEMBLY |
| *a | for Oil Filter Element Kit Type | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
| ★ | Precoated part | |
Do not apply lubricants to the threads |
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | CRANKSHAFT POSITION SENSOR | *4 | CRANKSHAFT TIMING GEAR KEY |
| *5 | CRANKSHAFT TIMING SPROCKET | *6 | NO. 1 CHAIN VIBRATION DAMPER |
| *7 | NO. 1 CRANKSHAFT POSITION SENSOR PLATE | *8 | NO. 2 CHAIN SUB-ASSEMBLY |
| *9 | O-RING | *10 | OIL PUMP DRIVE GEAR |
| *11 | OIL PUMP DRIVE SHAFT GEAR | *12 | CHAIN DAMPER SPRING |
| *13 | CHAIN TENSIONER PLATE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT HOUSING SUB-ASSEMBLY | *2 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
| *3 | CAMSHAFT TIMING GEAR ASSEMBLY | *4 | CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY |
| *5 | CYLINDER HEAD GASKET | *6 | CYLINDER HEAD SUB-ASSEMBLY |
| *7 | ENGINE COOLANT TEMPERATURE SENSOR | *8 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
| *9 | VALVE LASH ADJUSTER ASSEMBLY | *10 | VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY |
| *11 | VALVE STEM CAP | *12 | VALVE LIFT CONTROL ACTUATOR CONNECTOR |
| *13 | VALVE LIFT CONTROL ACTUATOR CLIP | *14 | STRAIGHT PIN |
| *15 | O-RING | *16 | PLATE WASHER |
| *17 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *T1 | 1st: 49 (500, 36) 2nd: Turn 90° 3rd: Turn 45° |
- | - |
ILLUSTRATION
| *1 | KNOCK CONTROL SENSOR | *2 | NO. 1 GENERATOR BRACKET |
| *3 | NO. 1 TAPER SCREW PLUG | *4 | NO. 2 OIL PAN SUB-ASSEMBLY |
| *5 | OIL PAN DRAIN PLUG | *6 | OIL PUMP ASSEMBLY |
| *7 | PCV VALVE SUB-ASSEMBLY | *8 | REAR ENGINE OIL SEAL |
| *9 | STIFFENING CRANKCASE ASSEMBLY | *10 | STIFFENING CRANKCASE RING PIN |
| *11 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
 |
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent | ★ | Precoated part |