SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P001313

DTC Code DTC Name
P001313 Camshaft Position "B" - Actuator Bank 1 Circuit Open

DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

B005BAOE73
DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001313 Camshaft Position "B" - Actuator Bank 1 Circuit Open Open or short in camshaft timing oil control valve assembly (for exhaust camshaft) circuit (1 trip detection logic).

  • Open or short in camshaft timing oil control valve assembly (for exhaust camshaft) circuit

  • Camshaft timing oil control valve assembly (for exhaust camshaft)

  • ECM

 Comes on DTC stored SAE: P0013

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly (for exhaust camshaft) circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the engine switch is on (IG) or the engine is running, the ECM will illuminate the MIL and store the DTC.

MONITOR STRATEGY

Required Sensors/Components Exhaust camshaft timing oil control valve assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch is on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch is on (IG) and turn the GTS on.

  6. Wait 5 seconds.

  7. Enter the following menus: Powertrain / Engine / Trouble Codes.

  8. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  10. Input the DTC: P001313.

  11. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

A01HHXRE04
*a Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft)

CAUTION / NOTICE / HINT

Tech Tips


  • If DTC P001313 is output, check the VVT system (for exhaust camshaft) circuit.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ DTC OUTPUT (DTC P001313)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTC after recording the freeze frame data and DTC.

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG) and wait 5 seconds.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine / Trouble Codes.

    9. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P001313 is output A
      DTC is not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)


    1. Inspect the camshaft timing oil control valve assembly (for exhaust camshaft).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)


    1. Disconnect the camshaft timing oil control valve assembly (for exhaust camshaft) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C10-2 - C20-38 (OE1+) Always Below 1 Ω
      C10-1 - C20-68 (OE1-) Always Below 1 Ω
      C10-2 or C20-38 (OE1+) - Body ground and other terminals Always 10 kΩ or higher
      C10-1 or C20-68 (OE1-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR