Click here

САЛЬНИК ПЕРЕДНЕГО ДИФФЕРЕНЦИАЛА ЗАМЕНА

Click here
Click here Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front differential oil seal removal/installation are shown below.

Table 1. Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Front wheel alignment adjustment

  1. Clear zero point calibration data and store system information.

  2. Perform yaw rate and acceleration sensor zero point calibration and store system information.

  • VSC disabled or malfunctions

  • DTCs are stored

  • Slip indicator light illuminates

  • ABS warning light illuminates

Click here
Click here

PROCEDURE


  1. Click here

    REMOVE REAR ENGINE UNDER COVER LH

    Click here

  2. Click here

    DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID


    1. A01IIIM

      Remove the refill plug and gasket from the rear transaxle case.

    2. A01IFWT

      Using a 10 mm hexagon socket wrench, remove the drain plug and gasket from the transaxle oil (CVT) pan sub-assembly, and drain the fluid.

    3. Install a new gasket and the drain plug to the transaxle oil (CVT) pan sub-assembly.

      49 N*m 500 kgf*cm 36 ft.*lbf

    4. Temporarily install the gasket and refill plug to the rear transaxle case.

      Tip:

      Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.

  3. Click here

    REMOVE FRONT DRIVE SHAFT ASSEMBLY

    Click here

  4. Click here

    REMOVE DRIVE SHAFT BEARING BRACKET

    Click here

  5. Click here

    REMOVE FRONT DRIVE SHAFT OIL SEAL LH


    1. Using SST, remove the front drive shaft oil seal LH from the transaxle case.

      09308-00010
      Note:

      Do not damage the transaxle case.

  6. Click here

    REMOVE FRONT DRIVE SHAFT OIL SEAL RH


    1. Using SST, remove the front drive shaft oil seal RH from the transaxle housing sub-assembly.

      09308-00010
      Note:

      Do not damage the transaxle housing sub-assembly.

  7. Click here

    INSTALL FRONT DRIVE SHAFT OIL SEAL RH


    1. Coat the lip of a new front drive shaft oil seal RH with MP grease.

    2. A01IGUKC01
      *a Depth

      Using SST and a hammer, install the front drive shaft oil seal RH to the transaxle housing sub-assembly.

      09316-10010
      09950-70010 09951-07100
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
      Note:

      • Be sure to install the front drive shaft oil seal RH in the correct direction.

      • Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

      • Do not damage the lip of the front drive shaft oil seal RH.

  8. Click here

    INSTALL FRONT DRIVE SHAFT OIL SEAL LH


    1. Coat the lip of a new front drive shaft oil seal LH with MP grease.

    2. A01IIAMC01
      *a Depth

      Using SST and a hammer, install the front drive shaft oil seal LH to the transaxle case.

      09316-10010
      09950-70010 09951-07150
      Standard Depth
      -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
      Note:

      • Be sure to install the front drive shaft oil seal LH in the correct direction.

      • Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

      • Do not damage the lip of the front drive shaft oil seal LH.

  9. Click here

    INSTALL DRIVE SHAFT BEARING BRACKET

    Click here

  10. Click here

    INSTALL FRONT DRIVE SHAFT ASSEMBLY

    Click here

  11. Click here

    ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

    Click here

  12. Click here

    INSPECT FOR FLUID LEAK

  13. Click here

    INSTALL REAR ENGINE UNDER COVER LH

    Click here