РАДИАТОР СНЯТИЕ

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the radiator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system

Click here

Memorize steering angle neutral point Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Initialize servo motor Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Power back door system

Click here

Removal/installtaion of the front television camera assembly or the radiator grille Television camera view adjustment Panoramic view monitor system

Click here

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

    Click here

  4. SEPARATE CENTER NO. 1 COWL TOP VENTILATOR LOUVER

    Click here

  5. REMOVE BATTERY

    Click here

  6. REMOVE FRONT BUMPER ASSEMBLY (for ALPHARD)

    Click here

  7. REMOVE FRONT BUMPER ASSEMBLY (for VELLFIRE)

    Click here

  8. REMOVE NO. 1 ENGINE UNDER COVER

    A01UEUG

    1. Remove the 8 bolts, 5 clips and No. 1 engine under cover.

  9. DRAIN ENGINE COOLANT

    Click here

  10. REMOVE INLET NO. 1 AIR CLEANER

    Click here

  11. REMOVE HOOD LOCK ASSEMBLY

    Click here

  12. REMOVE FRONT NO. 2 BUMPER SIDE SEAL LH (for ALPHARD)


    1. A01UCV4

      Remove the clip.

    2. Disengage the 2 claws and remove the front No. 2 bumper side seal LH.

  13. REMOVE FRONT NO. 2 BUMPER SIDE SEAL LH (for VELLFIRE)


    1. A01UCD6

      Remove the clip.

    2. Disengage the 2 claws and remove the front No. 2 bumper side seal LH.

  14. REMOVE FRONT NO. 2 BUMPER SIDE SEAL RH (for ALPHARD)


    1. A01UCXT

      Remove the clip.

    2. Disengage the 2 claws and remove the front No. 2 bumper side seal RH.

  15. REMOVE FRONT NO. 2 BUMPER SIDE SEAL RH (for VELLFIRE)


    1. A01UD48

      Remove the clip.

    2. Disengage the 2 claws and remove the front No. 2 bumper side seal RH.

  16. DISCONNECT NO. 1 RADIATOR HOSE


    1. A01UCF3

      Disengage the clamp and disconnect the No. 1 radiator hose from the radiator hose clamp.

    2. Slide the clip and disconnect the No. 1 radiator hose from the radiator assembly.

  17. DISCONNECT NO. 2 RADIATOR HOSE


    1. A01UFIP

      Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.

  18. DISCONNECT NO. 2 WATER BY-PASS HOSE


    1. A01UD4L

      Slide the clip and disconnect the No. 2 water by-pass hose from the radiator assembly.

  19. DISCONNECT NO. 3 WATER BY-PASS HOSE


    1. A01UD01

      Slide the clip and disconnect the No. 3 water by-pass hose from the radiator assembly.

  20. SEPARATE WATER BY-PASS PIPE SUB-ASSEMBLY


    1. A01UEF9

      Remove the 2 bolts and separate the water by-pass pipe sub-assembly from the upper radiator support sub-assembly.

  21. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    1. A01UEEH

      Disengage the clamp and disconnect the No. 1 cooler refrigerant suction hose from the bracket.

    2. A01UF6T

      Disconnect the 2 horn connectors.

    3. Disengage the 5 clamps and disconnect the wire harness from the upper radiator support sub-assembly.

    4. A01UEMM

      Disconnect the cooling fan motor connector and No. 2 cooling fan motor connector.

    5. Disengage the 3 clamps and disconnect the wire harness from the upper radiator support sub-assembly and fan shroud assembly.

    6. A01UDM1

      Disengage the clamp and disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.

    7. A01UCQ3

      Remove the 5 bolts and upper radiator support sub-assembly.

    8. Remove the 2 radiator support cushions.

  22. REMOVE NO. 2 FAN SHROUD


    1. A01UFBK

      Remove the 2 bolts.

    2. Disengage the 2 claws and remove the No. 2 fan shroud from the radiator assembly.

  23. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

    Click here

  24. DISCONNECT NO. 2 AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

    Click here

  25. REMOVE COOLER CONDENSER ASSEMBLY

    Click here

  26. REMOVE NO. 1 COOLER CONDENSER CUSHION

    Click here

  27. REMOVE RADIATOR ASSEMBLY


    1. A01UFLH

      Remove the radiator assembly with the fan shroud assembly from the vehicle.

    2. Remove the 2 lower radiator supports.

    3. A01UER0

      Remove the 2 bolts and fan shroud assembly from the radiator assembly.

      Note

      Do not damage the radiator assembly when removing the fan shroud assembly.