ВПУСКНОЙ КОЛЛЕКТОР СНЯТИЕ

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the intake manifold removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) Stop and start system

Click here

Memorize steering angle neutral point Panoramic view monitor system

Click here

Initialize back door lock Power door lock control system

Click here

Initialize servo motor Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Power back door system

Click here

Throttle body with motor assembly Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here

Cleaning the deposits from the throttle body with motor assembly

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  5. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

    Click here

  6. REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

    Click here

  7. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL

    Click here

  8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

    Click here

  9. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

    Click here

  10. REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)


    1. A01UCXR

      Disconnect the union to check valve hose from the vacuum hose clamp.

    2. Disengage the wire harness clamp.

    3. Disconnect the 2 vacuum hoses.

    4. Disconnect the vacuum switching valve assembly (for ACIS) connector.

    5. Remove the bolt and vacuum switching valve assembly (for ACIS) from the intake manifold.

  11. DISCONNECT NO. 2 VENTILATION HOSE


    1. A01UF4I

      Slide the clip and disconnect the No. 2 ventilation hose from the intake manifold.

  12. DISCONNECT UNION TO CHECK VALVE HOSE


    1. A01UCSI

      Slide the clip and disconnect the union to check valve hose from the intake manifold.

  13. DISCONNECT FUEL TUBE SUB-ASSEMBLY

    Click here

  14. DISCONNECT ENGINE WIRE


    1. A01UF6BC01
      A01UFKZ Nut
      A01UCWX Connector

      Remove the 3 nuts and disconnect the engine wire from the cylinder head cover sub-assembly.

    2. Disconnect the 12 connectors and disengage the wire harness clamp.

    3. A01UFLM

      Remove the 2 bolts and 2 wire harness clamp brackets from the intake manifold.

    4. A01UETN

      Remove the 2 bolts and disconnect the engine wire from the cylinder head sub-assembly.

    5. Remove the bolt and disconnect the engine wire from the wire harness bracket.

    6. Disconnect the 2 connectors and disengage the wire harness clamp.

    7. A01UEFX

      Disengage the wire harness clamp and disconnect the engine wire.

  15. REMOVE FUEL DELIVERY PIPE

    Click here

  16. REMOVE INTAKE MANIFOLD


    1. A01UD1L

      Slide the clip and disconnect the fuel vapor feed hose from the intake manifold.

    2. A01UCSG

      Disengage the 2 wire harness clamps.

    3. Disconnect the sensor wire connector.

    4. Remove the bolt and disconnect the wire harness clamp bracket from the intake manifold.

    5. A01UEG7N03

      Apply positive (+) battery voltage to terminal 8 (M-) and negative (-) battery voltage to terminal 4 (M+) of the sensor wire connector to close the 4 tumble control valves (TCV).

      Note


      • The 4 tumble control valves (TCV) may be damaged if they are not closed before removing the intake manifold.

      • Apply battery voltage for 1 to 3 seconds.

      • If battery voltage is applied for more than 3 seconds, the intake air control valve actuator (for TCV) may be damaged.

      • Do not allow the lead wires to contact the other terminals.

    6. A01UEQT

      Disengage the 2 wire harness clamps.

    7. Disconnect the intake air control valve actuator (for TCV) connector.

    8. A01UCKQ

      Remove the 6 bolts and intake manifold from the cylinder head sub-assembly.

      Note

      The 4 tumble control valves (TCV) may be damaged if they are not closed before removing the intake manifold.

      Tech Tips

      Connect the battery to the terminals of the intake air control valve actuator (for TCV) to operate the motor and close the 4 tumble control valves (TCV).

      Click here

    9. A01UF4V

      Remove the intake manifold to head gasket from the intake manifold.

    10. A01UDKZ

      Disconnect the 2 vacuum hoses and remove the No. 1 check valve from the intake manifold.

    11. A01UDA6

      Remove the bolt and wire harness clamp bracket from the intake manifold.