Click here

REAR BUMPER REASSEMBLY

Click here
Click here

PROCEDURE


  1. Click here

    INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. Install the rear bumper reinforcement sub-assembly with the 8 bolts.

      20 N*m 204 kgf*cm 15 ft.*lbf
  2. Click here

    INSTALL REAR BUMPER ENERGY ABSORBER


    1. A01VNDQ

      Engage the 2 guides to install the rear bumper energy absorber.

  3. Click here

    INSTALL REAR BUMPER SIDE SUPPORT LH


    1. A01VNPD

      Engage the guide and claw.

    2. A01VNTK

      Install the 2 screws.

    3. A01VO1J

      Install the rear bumper side support LH with 2 new grommets.

  4. Click here

    INSTALL REAR BUMPER SIDE SUPPORT RH

    Tip:

    Use the same procedure as for the LH side.

  5. Click here

    INSTALL NO. 2 REAR BUMPER SIDE SUPPORT LH


    1. A01VNQL

      Engage the 5 claws.

    2. A01VOEL

      Engage the 3 clips to install the No. 2 rear bumper side support LH as shown in the illustration.

  6. Click here

    INSTALL NO. 2 REAR BUMPER SIDE SUPPORT RH

    Tip:

    Use the same procedure as for the LH side.

  7. Click here

    INSTALL REAR BUMPER CENTER EXTENSION SUB-ASSEMBLY


    1. A01VO33

      Engage the 6 claws.

    2. A01VN7P

      Engage the 2 guides.

    3. Install the 2 outside moulding retainers.

    4. Install the 2 screws.

    5. Install the rear bumper center extension sub-assembly with the 6 clips.

  8. Click here

    INSTALL REFLEX REFLECTOR ASSEMBLY LH


    1. A01VMJS

      Engage the guide.

    2. Install the reflex reflector assembly LH with the screw.

  9. Click here

    INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

  10. Click here

    INSTALL REAR BUMPER PIECE LH


    1. A01VMSMC01
      *a Hook

      Engage the hook.

    2. Engage the 2 claws to install the rear bumper piece LH.

  11. Click here

    INSTALL REAR BUMPER PIECE RH

    Tip:

    Use the same procedure as for the LH side.

  12. Click here

    INSTALL REAR BUMPER PAD

    Tip:

    Use the same procedure for the RH side and LH side.


    1. Clean the rear bumper cover.


      1. Remove any remaining double-sided tape from the rear bumper cover.

      2. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new rear bumper pad.

      Tip:

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. A01VMW0C01
      *a Line

      Install the rear bumper pad as shown in the illustration.

      Tip:

      Install the rear bumper pad along the line marked on the rear bumper cover.

  13. Click here

    INSTALL REAR BUMPER SIDE MOULDING SUB-ASSEMBLY LH

    Click here

  14. Click here

    INSTALL REAR BUMPER SIDE MOULDING SUB-ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

  15. Click here

    INSTALL NO. 3 LUGGAGE ROOM WIRE (w/ LEXUS Parking Assist-sensor System)


    1. A01VOFC

      Engage the 2 clamps to install the No. 3 luggage room wire.

  16. Click here

    INSTALL NO. 1 ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here

  17. Click here

    INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ LEXUS Parking Assist-sensor System)

    Click here