ACTIVE REAR WING SYSTEM INITIALIZATION

INITIALIZATION

1. Initialization can be performed by using one of the following methods.

   	Initializing with the GTS	Initializing with the spoiler control switch	Initializing by driving the vehicle	Forced initialization
   When the active rear wing assembly has been removed/installed or replaced	○	-	-	○
   When the spoiler control ECU assembly has been replaced with a new one	○	○	○	-
   When the spoiler control ECU assembly has been replaced with one from another vehicle	○	-	-	○
   When the active rear wing has been stopped during operation	○	○	○	-
   When the active rear wing can be operated by manual and automatic operation but the active rear wing assembly position stored in the spoiler control ECU assembly and actual active rear wing position do not match	○	-	-	○

2. Initializing with the GTS

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the engine switch on (IG).

   3. Turn the GTS on.

   4. Enter following menus: Body Electrical / Active Rear Wing / Utility.

      
      
      1. Body Electrical > Active Rear Wing > Utility

         Tester Display
         Rear Wing Zero Point Calibration

      2. 
         
         1. 
            
      3. 
         
         10. 
             

   5. According to the GTS display perform initialization.

   6. After initialization is complete, check the rise and retract operations of the active rear wing.

      Click here

3. Initializing with the spoiler control switch

   Note:

   Check that the active rear wing system customize setting "Active Rear Wing Control" is set to "Permission" before performing the following procedure.

   Click here

   
   

   1. Turn the engine switch on (IG).

   2. Press the spoiler control switch to raise the active rear wing to the fully raised position.

   3. Press and hold the spoiler control switch until the active rear wing reaches the fully retracted position. (Initialization complete)

      Tip:

      If the spoiler control switch is released before the active rear wing reaches the fully retracted position, the active rear wing will operate in the reverse direction and rise to the fully raised position.

   4. After initialization is complete, check the rise and retract operations of the active rear wing.

      Click here

4. Initializing by driving the vehicle

   Note:

   Check that the active rear wing system customize setting "Active Rear Wing Control" is set to "Permission" before performing the following procedure.

   Click here

   
   

   1. When the active rear wing is in the fully raised position or fully retracted position

      
      

      1. Start the engine.

      2. Accelerate the vehicle to approximately 80 km/h or more*1 or approximately 130 km/h or more*2 to raise the active rear wing to the fully raised position.

      3. 
         

         • *1: When not in ECO mode

         • *2: When in ECO mode

      4. Decelerate the vehicle to below approximately 40 km/h to retract the active rear wing to the fully retracted position. (Initialization complete)

      5. After initialization is complete, check the rise and retract operations of the active rear wing.

         Click here

   2. When the active rear wing has been stopped during operation

      
      

      1. Start the engine.

      2. Accelerate the vehicle to approximately 25 km/h or more to raise the active rear wing to the fully raised position.

      3. Accelerate the vehicle to approximately 40 km/h or more.

      4. Decelerate the vehicle to below approximately 40 km/h to retract the active rear wing to the fully retracted position. (Initialization complete)

      5. After initialization is complete, check the rise and retract operations of the active rear wing.

         Click here

5. Forced initialization

   Note:

   Check that the active rear wing system customize setting "Active Rear Wing Control" is set to "Permission" before performing the following procedure.

   Click here

   
   

   1. Turn the engine switch on (IG).

   2. Press and hold the spoiler control switch until the active rear wing completes the following operations:

      Retract to the fully retracted position → pause for approximately 10 seconds → rise to the fully raised position (Forced initialization complete)

   3. After forced initialization is complete, check the rise and retract operations of the active rear wing.

      Click here