ROOF HEADLINING INSTALLATION

Click here Click here

PROCEDURE

1. Click here

   INSTALL ROOF HEADLINING ASSEMBLY

   
   

   1. Install a new grommet to the vehicle body.

      Tip:

      Use the same procedure for the RH side and LH side

   2. 

      *a	Clip (Black)
      *b	Clip (White)

      Install the 2 clips to the roof headlining assembly.

   3. 

      Put the roof headlining assembly into the vehicle through the front passenger door as shown in the illustration.

      Note:

      Do not damage the roof headlining assembly or vehicle interior.

   4. 

      for Roof Side (w/o Sliding Roof):

      
      

      1. Engage the 3 guides.

      2. Engage the 6 claws and 2 clips to install the roof headlining assembly.

      3. Install the 2 screws to the 2 coat hooks.

   5. 

      *a

      Guide

      *b

      Fastener

      for Roof Side (w/ Sliding Roof):

      
      

      1. Engage the 2 guides.

      2. Engage the 6 claws, 2 clips and 8 fasteners to install the roof headlining assembly.

      3. Install the 2 screws to the 2 coat hooks.

      4. Connect the connector to the sliding roof drive gear sub-assembly.

   6. for Front Pillar LH Side:

      
      

      1. Connect the 2 connectors.

      2. Engage the 3 clamps.

   7. for Windshield Glass Side:

      
      

      1. Connect each connector.

2. Click here

   INSTALL VISOR HOLDER (for LH Side)

   
   
   1. 

      Engage the 2 claws.

   2. Push in the visor holder as shown in the illustration.

3. Click here

   INSTALL VISOR ASSEMBLY LH

   
   

   1. Install the visor assembly LH with the 2 screws.

4. Click here

   INSTALL VISOR BRACKET COVER (for LH Side)

   
   
   1. 

      Engage the 4 claws to install the visor bracket cover.

5. Click here

   INSTALL ASSIST GRIP SUB-ASSEMBLY (for LH Side)

   
   
   1. 

      Install the clip to the assist grip.

      Tip:

      Use the same procedure for the RH side and LH side.

   2. Temporarily install a new assist grip cover to the assist grip as shown in the illustration.

      Tip:

      Use the same procedure for the RH side and LH side.

   3. 

      Engage the 2 clips to install the assist grip sub-assembly.

   4. 

      Engage the 2 claws to install the assist grip cover.

      Note:

      Make sure that 2 clips are engaged securely.

      Tip:

      Use the same procedure for the RH side and LH side.

6. Click here

   INSTALL VISOR HOLDER (for RH Side)

   Tip:

   Use the same procedure as for the LH side.

7. Click here

   INSTALL VISOR ASSEMBLY RH

   Tip:

   Use the same procedure as for the LH side.

8. Click here

   INSTALL VISOR BRACKET COVER (for RH Side)

   Tip:

   Use the same procedure as for the LH side.

9. Click here

   INSTALL ASSIST GRIP SUB-ASSEMBLY (for RH Side)

   Tip:

   Use the same procedure as for the LH side.

10. Click here

    INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    Click here

11. Click here

    INSTALL MAP LIGHT ASSEMBLY

    Click here

12. Click here

    INSTALL RAIN SENSOR (w/o Lane Departure Alert System)

    w/ Rain Sensor:

    Click here

13. Click here

    INSTALL RAIN SENSOR COVER (w/o Lane Departure Alert System)

    w/ Rain Sensor:

    Click here

14. Click here

    INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/o Lane Departure Alert System)

    Click here

15. Click here

    INSTALL NO. 2 LANE RECOGNITION COVER (w/ Lane Departure Alert System)

    Click here

16. Click here

    INSTALL NO. 1 LANE RECOGNITION COVER (w/ Lane Departure Alert System)

    Click here

17. Click here

    INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

18. Click here

    INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH

    
    

    1. Engage the 3 claws and 2 clips to install the roof side rail garnish assembly LH.

19. Click here

    INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH

    
    

    1. Engage the guide.

    2. Engage the claw and 4 clips to install the inner roof side garnish assembly LH.

20. Click here

    INSTALL CENTER PILLAR GARNISH ASSEMBLY LH

    
    

    1. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar garnish assembly LH.

    2. Engage the 2 guides and 4 claws to connect the belt guide of the front seat outer belt assembly LH.

    3. Engage the 3 claws and clip.

    4. Install the center pillar garnish assembly LH with the 2 screws.

21. Click here

    INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

    
    

    1. Connect the connector.

    2. Engage the clamp.

    3. Engage the 7 claws, 7 clips and guide to install the front quarter trim panel assembly LH.

    4. Install the 2 clips.

    5. Connect the belt guide of the rear seat 3 point type outer belt assembly LH with the bolt.

       21 N*m

       214 kgf*cm

       15 ft.*lbf

22. Click here

    INSTALL REAR SIDE SEATBACK ASSEMBLY LH

    Click here

23. Click here

    CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

    Click here

24. Click here

    CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

25. Click here

    INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

    Click here

26. Click here

    INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

27. Click here

    INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

28. Click here

    INSTALL CENTER PILLAR GARNISH ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

29. Click here

    INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

30. Click here

    INSTALL REAR SIDE SEATBACK ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

31. Click here

    CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

32. Click here

    CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

33. Click here

    INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tip:

    Use the same procedure as for the LH side.

34. Click here

    INSTALL REAR SEAT CUSHION LOCK HOOK

    Click here

35. Click here

    INSTALL REAR SEAT CUSHION ASSEMBLY

    Click here

36. Click here

    INSTALL FRONT PILLAR GARNISH LH

    
    

    1. Remove the protective cover.

    2. Make sure that the 2 front pillar garnish clips are not damaged.

       Note:

       If a front pillar garnish clip is damaged, replace the front pillar garnish clip with a new one.

    3. 

       *a	Front Pillar Garnish Clip (A)
       *b	Front Pillar Garnish Clip (B)

       Engage the 2 front pillar garnish clips to the front pillar garnish LH.

       Tip:

       Engage the 2 front pillar garnish clips so that it faces as shown in the illustration.

    4. 

       Push the front pillar garnish LH as shown in the illustration to engage the 3 guides.

    5. 

       Engage the 2 front pillar garnish clips to install the front pillar garnish LH.

       Tip:

       Make sure that the curtain shield airbag assembly LH is not pinched.

37. Click here

    INSTALL FRONT DOOR OPENING TRIM COVER LH

    
    
    1. 

       Engage the guide (B) and claw (B).

    2. Engage the 3 claws (A) and guide (A) to install the front door opening trim cover LH.

38. Click here

    INSTALL FRONT DOOR SCUFF PLATE LH

    
    

    1. Engage the 5 guides and 12 claws to install the front door scuff plate LH.

39. Click here

    INSTALL FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure as for the LH side.

40. Click here

    INSTALL FRONT DOOR OPENING TRIM COVER RH

    Tip:

    Use the same procedure as for the LH side.

41. Click here

    INSTALL FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure as for the LH side.

42. Click here

    INSTALL FRONT SEAT ASSEMBLY LH

    Click here

43. Click here

    INSTALL FRONT SEAT ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.