Click here

INSTRUMENT PANEL SAFETY PAD REMOVAL

Click here
Click here

PROCEDURE


  1. Click here

    PRECAUTION

    Click here

    Note:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. Click here

    ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  3. Click here

    CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)

    Click here

  4. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  5. Click here

    REMOVE CONSOLE BOX ASSEMBLY

    Click here

  6. Click here

    REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  7. Click here

    REMOVE FRONT DOOR OPENING TRIM COVER LH

    Click here

  8. Click here

    REMOVE INSTRUMENT SIDE PANEL LH


    1. B0065RY

      Disengage the claw and 4 clips as shown in the illustration.

    2. B0067XK

      Disengage the 2 guides to remove the instrument side panel LH as shown in the illustration.

  9. Click here

    REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. for LHD:


      1. B00667X

        Remove the 2 screws <C>.

      2. Disengage the 3 clips.

      3. Disengage the connector clamp.

      4. Disconnect each connector to remove the No. 1 instrument panel under cover sub-assembly.

    2. for RHD:


      1. B006694

        Remove the 2 screws <C>.

      2. Disengage the 3 clips.

      3. Disengage the connector clamp.

      4. Disconnect each connector to remove the No. 1 instrument panel under cover sub-assembly.

  10. Click here

    DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B0066Y4

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  11. Click here

    REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. B0067O8

      Disengage the 5 claws, 7 clips and guide.

    2. Disconnect each connector to remove the lower instrument panel finish panel sub-assembly.

  12. Click here

    REMOVE SKID CONTROL BUZZER (w/ Pre-collision System)

    Click here

  13. Click here

    REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  14. Click here

    REMOVE METER HOOD SUB-ASSEMBLY


    1. B00677E

      Disengage the 4 clips and 2 claws.

    2. B0067M6

      Disengage the 2 claws as shown in the illustration.

    3. B00655S

      Disengage the 7 clips and 3 guides as shown in the illustration.

    4. Disconnect the connector to remove the meter hood sub-assembly.

  15. Click here

    REMOVE COMBINATION METER ASSEMBLY

    Click here

  16. Click here

    REMOVE TELEMATICS TRANSCEIVER (w/ Telematics Transceiver)

    Click here

  17. Click here

    REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B00651U

      Disengage the 2 claws and 2 clips to remove the No. 1 instrument panel register assembly.

  18. Click here

    REMOVE HORN BUTTON ASSEMBLY

    Click here

  19. Click here

    REMOVE STEERING WHEEL ASSEMBLY

    w/ Lane Departure Alert System:

    Click here

    w/o Lane Departure Alert System:

    Click here

  20. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure as for the LH side.

  21. Click here

    REMOVE FRONT DOOR OPENING TRIM COVER RH

    Tip:

    Use the same procedure as for the LH side.

  22. Click here

    REMOVE INSTRUMENT SIDE PANEL RH


    1. B00672P

      Disengage the claw and 4 clips as shown in the illustration.

    2. B00677H

      Disengage the 2 guides to remove the instrument side panel RH as shown in the illustration.

    3. w/ Airbag Cut Off Switch:


      1. Disconnect the connector.

  23. Click here

    REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B00686IN01

      Disengage the 4 clips and 2 guides as indicated by the arrows, in the order shown in the illustration.

    2. Disconnect each connector to remove the No. 2 instrument panel under cover sub-assembly.

  24. Click here

    REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  25. Click here

    REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. B0066O1

      Remove the 2 screws <C>.

    2. B0067G0

      Open the glove compartment door assembly.

    3. B0065S1

      Remove the 3 screws <C>.

    4. B0065JI

      Close the glove compartment door assembly.

    5. B0065X4

      Disengage the 5 claws.

    6. Disengage the connector clamp.

    7. Disconnect each connector to remove the glove compartment door assembly.

  26. Click here

    REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B0065JH

      Disengage the claw as shown in the illustration.

    2. B006737

      Disengage the 2 claws and 2 clips to remove the No. 2 instrument panel register assembly as shown in the illustration.

  27. Click here

    REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET

    Click here

  28. Click here

    REMOVE AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  29. Click here

    REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B0066QN

      Disengage the 4 claws and 4 clips.

    2. Disconnect the connector to remove the center instrument panel register assembly.

  30. Click here

    REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. B0067DRC01
      B00667M Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Using a moulding remover, disengage the 3 claws as shown in the illustration.

    3. Disengage the 3 guides to remove the instrument cluster finish panel sub-assembly as shown in the illustration.

  31. Click here

    REMOVE MULTI-DISPLAY ASSEMBLY WITH BRACKET

    Click here

  32. Click here

    REMOVE FRONT PILLAR GARNISH LH

    Click here

  33. Click here

    REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B00674B

      Disengage the 2 clips and 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.

  34. Click here

    REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

    Click here

  35. Click here

    REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. B00683BC01
      B00667M Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Using a moulding remover, disengage the 4 claws and 4 clips to remove the instrument cluster finish panel assembly as shown in the illustration.

  36. Click here

    REMOVE FRONT NO. 3 SPEAKER ASSEMBLY

    Click here

  37. Click here

    REMOVE FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure as for the LH side.

  38. Click here

    REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B0066FR

      Disengage the 2 clips and 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.

  39. Click here

    REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tip:

    Use the same procedure as for the LH side.

  40. Click here

    REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT


    1. B0065M6

      Disengage the 3 clips and 2 claws to remove the instrument cluster finish panel ornament as shown in the illustration.

  41. Click here

    DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

    Click here

  42. Click here

    REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. B0067A9C01
      *1 Room Temperature Sensor - -

      Disengage the 2 claws to disconnect the room temperature sensor.

    2. Disconnect each connector.

    3. Disengage each clamp.

    4. B0065T5C05
      *a Bolt <A> *b Bolt <B>

      Remove the 13 bolts <A>, 2 bolts <B> and nut <E>.

    5. B0066RJ

      Disengage the 4 guides and remove the instrument panel safety pad sub-assembly as shown in the illustration.

      Note:

      • Do not damage the instrument panel safety pad sub-assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.