Click here

IMMOBILISER SYSTEM Immobiliser System does not Operate Properly

Click here
Click here
DTC Code DTC Name
  Immobiliser System does not Operate Properly
Click here

DESCRIPTION

The immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

Click here

WIRING DIAGRAM

Click here

Click here

CAUTION / NOTICE / HINT

Note:

  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

    Click here

  • Before replacing the ECM or ID code box (immobiliser code ECU), refer to Service Bulletin.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

Tip:

If a immobiliser system or SFI system DTC is output, first perform troubleshooting for the immobiliser system or SFI system DTC.

Click here

PROCEDURE


  1. Click here

    CHECK FOR DTC


    1. Check for DTCs.


      1. Body Electrical > Entry&Start > Trouble Codes


      Result
      Result Proceed to
      DTCs are not output A
      DTCs are output B

  2. Click here

    CHECK WHETHER ENGINE STARTS


    1. Check that the engine starts 5 seconds after the engine switch turned on (IG).

      OK
      Engine starts normally.
      Result
      Proceed to
      OK
      NG

  3. Click here

    CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)


    1. Disconnect the O80 ID code box (immobiliser code ECU) connector.

    2. Disconnect the A77 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O80-3 (EFII) - A77-9 (IMO) Always Below 1 Ω
      O80-4 (EFIO) - A77-8 (IMI) Always Below 1 Ω
      O80-3 (EFII) or A77-9 (IMO) - Body ground Always 10 kΩ or higher
      O80-4 (EFIO) or A77-8 (IMI) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. Click here

    REGISTER ECU COMMUNICATION ID


    1. Register the ECU communication ID.

      Tip:

      Refer to Service Bulletin.

      Result
      Proceed to
      NEXT

  5. Click here

    CHECK WHETHER ENGINE STARTS


    1. Check that the engine starts.

      OK
      Engine starts normally.
      Result
      Proceed to
      OK
      NG

    • OK

      END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

    • NGClick here
  6. Click here

    REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


    1. Replace the ID code box (immobiliser code ECU) with a new one.

      Tip:

      Refer to Service Bulletin.

      Result
      Proceed to
      NEXT

  7. Click here

    REGISTER ECU COMMUNICATION ID


    1. Register the ECU communication ID.

      Tip:

      Refer to Service Bulletin.

      Result
      Proceed to
      NEXT

  8. Click here

    CHECK WHETHER ENGINE STARTS


    1. Check that the engine starts.

      OK
      Engine starts normally.
      Result
      Proceed to
      OK
      NG

    • OK

      END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

    • NG

      GO TO SFI SYSTEM w/ Canister Pump Module:Click here

      GO TO SFI SYSTEM w/o Canister Pump Module:Click here