Click here

POWER DOOR LOCK CONTROL SYSTEM, Diagnostic DTC:B1243

Click here
Click here
DTC Code DTC Name
B1243 GSW Terminal Circuit Malfunction
Click here

DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU (multiplex network body ECU) is detected, DTC B1243 will be stored.

Tip:

If DTC B1243 is stored, the automatic door lock function, and collision door lock release function will be prohibited.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1243 GSW Terminal Circuit Malfunction A malfunction occurs in the GSW input circuit of the main body ECU (multiplex network body ECU).

  • Main body ECU (multiplex network body ECU)

  • Airbag ECU assembly

  • Wire harness or connector
Table 1. *1 Instrument Panel Junction Block Assembly *2 Airbag ECU Assembly *3 Main Body ECU (Multiplex Network Body ECU)
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

Click here

PROCEDURE


  1. Click here

    CHECK DTC OUTPUT


    1. Clear the DTCs.

      Click here


      1. Body Electrical > Main Body > Clear DTCs


    2. Recheck for DTCs.


      1. Body Electrical > Main Body > Trouble Codes


      OK
      DTC B1243 is not output.
      Result
      Proceed to
      OK
      NG

  2. Click here

    CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (GSW VOLTAGE)


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note:

      Turning the engine switch on (IG) with the airbag sensor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    2. Disconnect the O50 airbag sensor assembly connector.

    3. Connect the cable to the negative (-) battery terminal.

    4. B0066RUC12
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O50-18 (GSW) - Body ground Engine switch on (IG) 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG

  3. Click here

    REPLACE AIR BAG ECU ASSEMBLY


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Replace the airbag sensor assembly.

      Click here

      Result
      Proceed to
      NEXT

  4. Click here

    CHECK DTC OUTPUT


    1. Clear the DTCs.

      Click here


      1. Body Electrical > Main Body > Clear DTCs


    2. Recheck for DTCs.


      1. Body Electrical > Main Body > Trouble Codes


      OK
      DTC B1243 is not output.
      Result
      Proceed to
      OK
      NG

    • OK

      END (AIRBAG ECU ASSEMBLY WAS DEFECTIVE)

    • NG

      REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)Click here

  5. Click here

    CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Disconnect the O50 airbag sensor assembly connector.

    3. Disconnect the 4A instrument panel junction block assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O50-18 (GSW) - 4A-7 Always Below 1 Ω
      4A-7 or O50-18 (GSW) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      Click here

    2. B00659DC02
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

      Remove the main body ECU (multiplex network body ECU).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      MB-24 (GSW) - 4A-7 Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)Click here

    • NG

      REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLYClick here