Click here

CAN COMMUNICATION SYSTEM Torque Vectoring Differential ECU Communication Stop Mode

Click here
Click here
DTC Code DTC Name
  Torque Vectoring Differential ECU Communication Stop Mode
Click here

DESCRIPTION

Detection Item Symptom Trouble Area
Torque Vectoring Differential ECU Communication Stop Mode

Either condition is met:


  • "TVD" is not displayed on the CAN Bus Check screen of the GTS

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Torque Vectoring Differential ECU Communication Stop Mode" in "DTC Combination Table" are output

    Click here

  • Torque vectoring differential ECU assembly branch line or connector

  • Power source circuit of torque vectoring differential ECU assembly

  • Torque vectoring differential ECU assembly ground circuit

  • Torque vectoring differential ECU assembly
B0066WZE01
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Turn the engine switch on (IG) and wait at least 2 seconds.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tip:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

Click here

PROCEDURE


  1. Click here

    CHECK FOR OPEN IN CAN BUS LINES (TORQUE VECTORING DIFFERENTIAL ECU ASSEMBLY BRANCH LINE)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. B0065KTC01
      *a

      Front view of wire harness connector

      (to Torque Vectoring Differential ECU Assembly)

      Disconnect the T43 torque vectoring differential ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T43-1 (CA1H) - T43-9 (CA1L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Result
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TORQUE VECTORING DIFFERENTIAL ECU ASSEMBLY)

  2. Click here

    CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    1. B006793C01
      *a

      Front view of wire harness connector

      (to Torque Vectoring Differential ECU Assembly)

      Disconnect the T27 torque vectoring differential ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T27-3 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

    3. Reconnect the cable to the negative (-) battery terminal.

    4. B0065KTC02
      *a

      Front view of wire harness connector

      (to Torque Vectoring Differential ECU Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      T43-14 (IG1) - Body ground Engine switch on (IG) 11 to 14 V
      T43-16 (BATT) - Body ground Always 11 to 14 V
      Result
      Result
      OK
      NG

    • OK

      REPLACE TORQUE VECTORING DIFFERENTIAL ECU ASSEMBLYClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)