CAN COMMUNICATION SYSTEM Spoiler Control ECU Communication Stop Mode

DESCRIPTION

Detection Item Symptom Trouble Area
Spoiler Control ECU Communication Stop Mode

Either condition is met:


  • Communication stop for "Active Rear Wing" is indicated on the "Communication Bus Check" screen of the GTS.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Spoiler Control ECU Communication Stop Mode" in "DTC Combination Table" are output

    Click here


  • Spoiler control ECU assembly branch line or connector

  • Power source circuit of spoiler control ECU assembly

  • Spoiler control ECU assembly ground circuit

  • Spoiler control ECU assembly

WIRING DIAGRAM

Figure 1. for LHD:

B0065R6E06

Figure 2. for RHD:

B0065R6E07

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

Note


  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips


  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE


  1. CHECK FOR OPEN IN CAN BUS LINES (SPOILER CONTROL ECU BRANCH LINE)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. B00650CC01
      *a

      Front view of wire harness connector

      (to Spoiler Control ECU Assembly)

      Disconnect the U38 spoiler control ECU assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U38-10 (CANP) - U38-11 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Result
      Result
      OK
      NG

    NG

    REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (SPOILER CONTROL ECU ASSEMBLY)

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    1. B00650CC02
      *a

      Front view of wire harness connector

      (to Spoiler Control ECU Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U38-1 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

    2. Reconnect the cable to the negative (-) battery terminal.

    3. B00650CC03
      *a

      Front view of wire harness connector

      (to Spoiler Control ECU Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U38-16 (IG) - Body ground Engine switch on (IG) 11 to 14 V
      U38-18 (ECUB) - Body ground Always 11 to 14 V
      Result
      Result
      OK
      NG

    OK

    REPLACE SPOILER CONTROL ECU ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)