Click here

BLIND SPOT MONITOR SYSTEM, Diagnostic DTC:C1AB5

Click here
Click here
DTC Code DTC Name
C1AB5 Open in Outer Mirror Indicator(Slave)
Click here

DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB5 Open in Outer Mirror Indicator(Slave)
  • Both of the following conditions are met:

  • The blind spot monitor main switch (warning canceling switch assembly) is on


  • The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator

  • Outer mirror RH

  • Outer rear view mirror assembly RH

  • Wire harness or connector

  • Blind spot monitor sensor RH

  • Outer mirror control ECU assembly RH
Click here

WIRING DIAGRAM


Click here
  1. B0067DKE93
Click here

CAUTION / NOTICE / HINT

Note:

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

Click here

PROCEDURE


  1. Click here

    CHECK DTC


    1. Clear the DTCs.

      Click here


      1. Body Electrical > Blind Spot Monitor Slave > Clear DTCs


    2. Recheck for DTCs and check if the same DTC is output again.


      1. Body Electrical > Blind Spot Monitor Slave > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

  2. Click here

    CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND)


    1. Disconnect the U47 blind spot monitor sensor RH connector.

    2. Disconnect the R12 outer mirror control ECU assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      U47-4 (OMIR) - R12-13 (BDSR) Always Below 1 Ω
      R12-7 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. Click here

    INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH


    1. Disconnect the R13 outer mirror control ECU assembly RH connector.

    2. B0066DFC53
      *a

      Component without harness connected

      (Outer Mirror Control ECU Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R12-13 (BDSR) - R13-8 (BDIR) Always Below 1 Ω
      R12-7 (GND) - R13-12 (HTR-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

  4. Click here

    CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)


    1. Disconnect the R7 outer rear view mirror assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R7-8 (BSR+) - R13-8 (BDIR) Always Below 1 Ω
      R7-12 (-) - R13-12 (HTR-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. Click here

    INSPECT OUTER MIRROR ACTUATOR ASSEMBLY RH


    1. Disconnect the IND2 outer mirror RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R7-8 (BSR+) - IND2-2 (+) Always Below 1 Ω
      R7-12 (-) - IND2-1 (-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

  6. Click here

    INSPECT OUTER MIRROR RH


    1. Remove the outer mirror RH.

      Click here

    2. Inspect the outer rear view mirror indicator RH on the outer mirror RH.

      Click here

      Result
      Proceed to
      OK
      NG