Click here

PARKING ASSIST MONITOR SYSTEM(w/o Parallel Parking Assist Function) DIAGNOSIS SYSTEM

Click here
Click here
Click here

  1. PARKING ASSIST MONITOR SYSTEM DIAGNOSTIC MODE


    1. In diagnostic mode for the parking assist monitor system, signals received by the radio receiver assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the multi-display assembly.

      Note:

      Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

      Click here

      Tip:

      The displayed items may differ depending on vehicle specifications.

  2. B0066XVE01
    Table 2.
    *1 or
    B00675NE01
    Table 1. Example
    *1 Start diagnostic mode
    *2 or

    DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION)

  3. B0067GF
    B0066HKE01
    Table 3. Example
    *1 Start diagnostic mode
    *2 or

    DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION)

  4. VEHICLE SIGNAL CHECK

    Tip:

    Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Start diagnostic mode.


    2. B0066EM

      Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

    3. B006501

      Select "Vehicle Signal" on the "Function Check/Setting I" screen.

    4. B0065YZ

      Vehicle Signal Check Mode


      1. When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".


        Tip:

        • Only conditions having inputs are displayed.

        • This screen displays vehicle signals input to the radio receiver assembly.

    5. Finish diagnostic mode.


  5. Tip:

    Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    SIGNAL CHECK (PARKING ASSIST MONITOR SYSTEM INPUT SIGNALS)


    1. Start diagnostic mode.



      1. B0066EM

        Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

      2. B006501

        Select "Camera Setting" on the "Function Check/Setting I" screen.

        Tip:

        After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the rear television camera assembly was replaced.

        Parking Assist Monitor System Initialization Screen Transition
        Not performed Signal Check screen
        Performed Mode Setting screen
      3. B0065O1

        When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Signal Check" screen.

        Tip:

        To select a grayed out item, select and hold the item for 2 seconds or more.

    2. B0065Y7

      Signal Check


      1. On the "Signal Check" screen, it is possible to inspect the state of signals and check the settings.

        Item Inspection Detail Note
        CAN CAN communication signal input When "CHK" (red) is displayed, selecting "Next" will not change the screen to the next screen.
        Tip:

        • When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

        • If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".

    3. CAN inspection

      Tip:

      If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs.

      Click here

    4. Finish diagnostic mode.


  6. CAMERA SYNCHRONOUS ERROR HISTORY

    Tip:

    This function is used to check the date and time of occurrence when a camera synchronous error occurs.


    1. Check camera synchronous error history.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Camera Synchronous Error History.


        1. Body Electrical > Navigation System > Utility
          Tester Display
          Camera Synchronous Error History




      5. When an item is stored for Camera Synchronous Error History, record it before repairing the multi-display assembly and rear television camera assembly.

        Tip:

        Camera Synchronous Error History can store up to 5 history data items. If a new camera synchronous error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

    2. Clear camera synchronous error history.


      1. When DTCs are cleared using any of the following operations, Camera Synchronous Error History will be cleared as well.



        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  7. VIDEO DEVICE CONNECTION CHECK


  8. CALIBRATION WHEN SERVICING VEHICLE

    Note:

    Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

    Click here