Click here

PARKING ASSIST MONITOR SYSTEM(w/ Parallel Parking Assist Function) HOW TO PROCEED WITH TROUBLESHOOTING

Click here
Click here
DTC Code DTC Name
  HOW TO PROCEED WITH TROUBLESHOOTING
Click here

CAUTION / NOTICE / HINT

Tip:
  • Use the following procedure to troubleshoot the parking assist monitor system.

  • *: Use the GTS.

Click here

PROCEDURE


  1. Click here

    VEHICLE BROUGHT TO WORKSHOP

    Result
    Proceed to
    NEXT

  2. Click here

    CUSTOMER PROBLEM ANALYSIS


    1. Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

      Tip:

      The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.

      Problem Symptom Cause

      • Both of the following conditions are met:
      • The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced.

      • DTC C1622 is output as "Hist" only.*

      The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.

      *: DTCs output as "Hist" will not be output again after DTCs are cleared.

      Result
      Proceed to
      NEXT

  3. Click here

    INSPECT BATTERY VOLTAGE


    1. Measure the battery voltage.

      Standard Voltage
      11 to 14 V

      If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

      Result
      Proceed to
      NEXT

  4. Click here

    SYSTEM CHECK


    1. Check the vehicle specification.

      Result
      Result Proceed to
      w/ Navigation System A
      w/o Navigation System B

  5. Click here

    CHECK NAVIGATION SYSTEM


    1. Refer to Navigation System.

      Click here

      Result
      Result Proceed to
      Navigation system is normal A
      Navigation system is abnormal B

  6. Click here

    CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*


    1. Use the GTS to check if the CAN communication system is functioning normally.

      Click here

      Result
      Result Proceed to
      CAN communication system DTCs are not output A
      CAN communication system DTCs are output B

  7. Click here

    CHECK FOR DTC*


    1. Check for DTCs and make a note of any codes that are output.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs. Try to reproduce the DTCs by duplicating the detection conditions of the DTCs.

      Click here


      1. Body Electrical > Navigation System > Trouble Codes


      Result
      Result Proceed to
      No DTCs are output A
      DTCs are output B

  8. Click here

    PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table.

      Click here

      Result
      Result Proceed to
      Fault is not listed in Problem Symptoms Table A
      Fault is listed in Problem Symptoms Table B

  9. Click here

    OVERALL ANALYSIS AND TROUBLESHOOTING


    1. Diagnosis System

      Click here

    2. Terminals of ECU

      Click here

      Result
      Proceed to
      NEXT

  10. Click here

    ADJUST, REPAIR OR REPLACE

    Result
    Proceed to
    NEXT

  11. Click here

    CONFIRMATION TEST

    Result
    Proceed to
    NEXT

    • NEXT

      END

  12. Click here

    CHECK AUDIO AND VISUAL SYSTEM (w/ Parking Assist Monitor System)


    1. Refer to Audio and Visual System (w/ Parking Assist Monitor System).

      Click here

      Result
      Result Proceed to
      Audio and visual system (w/ Parking Assist Monitor System) is normal A
      Audio and visual system (w/ Parking Assist Monitor System) is abnormal B

    • AClick here

      GO TO STEP 6

    • B

      GO TO AUDIO AND VISUAL SYSTEM (w/ Parking Assist Monitor System)Click here