Click here

SPIRAL CABLE INSTALLATION

Click here
Click here

PROCEDURE


  1. Click here

    INSPECT SPIRAL CABLE SUB-ASSEMBLY

    Note:

    If the steering sensor is installed to a misaligned spiral cable sub-assembly, spiral cable with sensor sub-assembly malfunction DTCs, such as DTC B1801, C1231 and C1433, will be stored and it will be impossible to clear them. If this happens, replace the spiral cable with sensor sub-assembly with a new one.


    1. B00652OC01
      *A w/o Steering Heater *B w/ Steering Heater
      *C Flat Cable Type *D Colored Roller Type
      *a Inspection Window *b Alignment Mark
      *c Colored Roller *d Flat Cable

      Check if the spiral cable sub-assembly is centered.


      • OK:

      • The connector is positioned at the top.

      • The alignment marks are aligned correctly.

      • The colored roller or flat cable can be seen in the inspection window.

    2. If the spiral cable sub-assembly is not centered, center it.

      Note:

      Make sure to observe the following precautions, otherwise the spiral cable sub-assembly may be damaged.


      • Release the interlock before rotating the spiral cable sub-assembly.

      • Do not rotate the spiral cable sub-assembly using the airbag wire harness.

      • Do not rotate the spiral cable sub-assembly with excessive force.


      1. B00653UC03
        *a Interlock

        While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

        Note:

        If the spiral cable sub-assembly is rotated clockwise in this step, it may be damaged and may no longer be able to be centered. Make sure to only rotate the spiral cable sub-assembly counterclockwise.

        Tip:

        If the interlock is engaged, the spiral cable sub-assembly will lock when the connector is near at the top or bottom of the rotation of the spiral cable sub-assembly.

      2. B0067E4

        If the connector is not positioned at the bottom of the rotation of the spiral cable sub-assembly when the spiral cable sub-assembly is turned until it stops, turn the spiral cable sub-assembly clockwise until the connector is positioned at the bottom as shown in the illustration.

      3. B00681DC02
        *a Interlock

        While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly clockwise approximately 2.5 times.

        Note:

        If the spiral cable sub-assembly is rotated clockwise 5 times or more from the point at which it stops and the connector is positioned at the bottom, the spiral cable sub-assembly may be damaged.

        Tip:

        If the interlock is engaged, the spiral cable sub-assembly will lock when the connector is near at the top or bottom of the rotation of the spiral cable sub-assembly.

      4. B00652OC01
        *A w/o Steering Heater *B w/ Steering Heater
        *C Flat Cable Type *D Colored Roller Type
        *a Inspection Window *b Alignment Mark
        *c Colored Roller *d Flat Cable

        Check that the spiral cable sub-assembly is centered.


        • OK:

        • The connector is positioned at the top.

        • The alignment marks are aligned correctly.

        • The colored roller or flat cable can be seen in the inspection window.

        Note:

        If the spiral cable sub-assembly cannot be centered, it may be damaged. Replace the spiral cable sub-assembly with a new one.

  2. Click here

    INSTALL SPIRAL CABLE SUB-ASSEMBLY


    1. B0066CEC06
      *a Guide
      *b Pin
      *c Lock Pin

      Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.

      Note:

      • Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.

      • Do not damage the pins of the spiral cable sub-assembly and guides of the steering sensor.

      • The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.

    2. B0065W7

      Remove the lock pin from the steering sensor.

  3. Click here

    INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note:

    • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).

    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the front wheels are aligned facing straight ahead.

    4. Engage the 3 claws to install the spiral cable with sensor sub-assembly.

    5. Connect each connector.

  4. Click here

    INSTALL STEERING COLUMN COVER

    Click here

  5. Click here

    ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  6. Click here

    INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. B0067MIC02
      *A w/o Steering Heater
      *B w/ Steering Heater
      *C Flat Cable Type
      *D Colored Roller Type
      *a Inspection Window
      *b Flat Cable
      *c Colored Roller

      Check if the spiral cable with sensor sub-assembly is centered.


      • OK:

      • The connector is positioned at the top.

      • The colored roller or flat cable can be seen in the inspection window.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.

      Note:

      Make sure to observe the following precautions, otherwise the spiral cable with sensor sub-assembly may be damaged.


      • Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

      • Release the interlock before rotating the spiral cable with sensor sub-assembly.

      • Do not rotate the spiral cable with sensor sub-assembly using the airbag wire harness.

      • Do not rotate the spiral cable with sensor sub-assembly with excessive force.


      1. B0065QQC01
        *A w/o Steering Heater
        *B w/ Steering Heater
        *a Interlock

        While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

        Note:

        If the spiral cable with sensor sub-assembly is rotated clockwise in this step, it may be damaged and may no longer be able to be centered. Make sure to only rotate the spiral cable with sensor sub-assembly counterclockwise.

        Tip:

        If the interlock is engaged, the spiral cable with sensor sub-assembly will lock when the connector is near at the top or bottom of the rotation of the spiral cable with sensor sub-assembly.

      2. B0066G9C01
        *A w/o Steering Heater
        *B w/ Steering Heater

        If the connector is not positioned at the bottom of the rotation of the spiral cable with sensor sub-assembly when the spiral cable with sensor sub-assembly is turned until it stops, turn the spiral cable with sensor sub-assembly clockwise until the connector is positioned at the bottom as shown in the illustration.

      3. B00680CC01
        *A w/o Steering Heater
        *B w/ Steering Heater
        *a Interlock

        While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times.

        Note:

        If the spiral cable with sensor sub-assembly is rotated clockwise 5 times or more from the point at which it stops and the connector is positioned at the bottom, the spiral cable with sensor sub-assembly may be damaged.

        Tip:

        If the interlock is engaged, the spiral cable with sensor sub-assembly will lock when the connector is near at the top or bottom of the rotation of the spiral cable with sensor sub-assembly.

      4. B0067MIC02
        *A w/o Steering Heater
        *B w/ Steering Heater
        *C Flat Cable Type
        *D Colored Roller Type
        *a Inspection Window
        *b Flat Cable
        *c Colored Roller

        Check that the spiral cable with sensor sub-assembly is centered.


        • OK:

        • The connector is positioned at the top.

        • The colored roller or flat cable can be seen in the inspection window.

        Note:

        If the spiral cable with sensor sub-assembly cannot be centered, it may be damaged. Replace the spiral cable with sensor sub-assembly with a new one.

  7. Click here

    INSTALL STEERING WHEEL ASSEMBLY

    Click here

  8. Click here

    ADJUST PARKING ASSIST SYSTEM (w/ Parking Assist Monitor System)

    Click here