Click here

NAVIGATION SYSTEM, Diagnostic DTC:B15C3

Click here
Click here
DTC Code DTC Name
B15C3 Speaker Output Short
Click here

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit.

  • Harness or connector

  • Speaker

  • Stereo component amplifier assembly

  • Telematics transceiver*

*: w/ Manual (SOS) Switch

B0067GSE04
Figure 2. for 17 Speakers B0065A2E16
B0065NAE45
Figure 1. for 10 Speakers
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

Click here

PROCEDURE


  1. Click here

    CHECK MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 10 Speakers (w/ Manual (SOS) Switch) A
      for 10 Speakers (w/o Manual (SOS) Switch) B
      for 17 Speakers (w/ Manual (SOS) Switch) C
      for 17 Speakers (w/o Manual (SOS) Switch) D

  2. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O65 telematics transceiver connector.

    3. Disconnect the O55 front No. 2 speaker assembly LH connector.

    4. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    5. Disconnect the O56 front No. 3 speaker assembly connector.

    6. Disconnect the T25 and U35 rear speaker assembly connectors.

    7. Disconnect the T24 rear No. 3 speaker assembly connector.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) or O65-2 (SPI+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O65-3 (SPI-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      T20-9 (RR+) or T25-1 - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T25-2 - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U35-1 - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U35-2 - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. Click here

    CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)


    1. Disconnect the O65 telematics transceiver connector.

    2. Disconnect the O54 front No. 2 speaker assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O65-5 (SPO+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      O65-6 (SPO-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. Click here

    INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. B00651DC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

  5. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    4. Disconnect the O56 front No. 3 speaker assembly connector.

    5. Disconnect the T25 and U35 rear speaker assembly connectors.

    6. Disconnect the T24 rear No. 3 speaker assembly connector.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      T20-9 (RR+) or T25-1 - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T25-2 - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U35-1 - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U35-2 - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  7. Click here

    INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  8. Click here

    INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  9. Click here

    INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  10. Click here

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

    3. Clear the DTCs.


      1. Body Electrical > Navigation System > Clear DTCs


    4. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END

    • NG

      REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLYClick here

  11. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O65 telematics transceiver connector.

    3. Disconnect the O55 front No. 2 speaker assembly LH connector.

    4. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    5. Disconnect the O56 front No. 3 speaker assembly connector.

    6. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    7. Disconnect the T23 and U34 rear header speaker assembly connectors.

    8. Disconnect the T24 rear No. 3 speaker assembly connector.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) or O65-2 (SPI+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O65-3 (SPI-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      T20-9 (RR+) or T26-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T26-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U36-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U36-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-11 (SR+) or T23-2 (+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) or T23-1 (-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) or U34-2 (+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) or U34-1 (-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. Click here

    CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - BODY GROUND)


    1. Disconnect the O65 telematics transceiver connector.

    2. Disconnect the O54 front No. 2 speaker assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O65-5 (SPO+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      O65-6 (SPO-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  13. Click here

    CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the T25 and U35 rear speaker assembly connectors.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T26-4 (+) or T25-1 - Body ground Always 10 kΩ or higher
      T26-2 (-) or T25-2 - Body ground Always 10 kΩ or higher
      U36-4 (+) or U35-1 - Body ground Always 10 kΩ or higher
      U36-2 (-) or U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  14. Click here

    INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. B00651DC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

  15. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    4. Disconnect the O56 front No. 3 speaker assembly connector.

    5. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    6. Disconnect the T23 and U34 rear header speaker assembly connectors.

    7. Disconnect the T24 rear No. 3 speaker assembly connector.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) or O54-2 (+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 (-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 (+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 (-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) or O56-2 (+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 (-) - Body ground Always 10 kΩ or higher
      T20-9 (RR+) or T26-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-24 (RR-) or T26-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-8 (RL+) or U36-3 (+TW) - Body ground Always 10 kΩ or higher
      T20-23 (RL-) or U36-1 (-TW) - Body ground Always 10 kΩ or higher
      T20-11 (SR+) or T23-2 (+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) or T23-1 (-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) or U34-2 (+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) or U34-1 (-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  16. Click here

    CHECK HARNESS AND CONNECTOR (REAR NO. 2 SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the T25 and U35 rear speaker assembly connectors.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T26-4 (+) or T25-1 - Body ground Always 10 kΩ or higher
      T26-2 (-) or T25-2 - Body ground Always 10 kΩ or higher
      U36-4 (+) or U35-1 - Body ground Always 10 kΩ or higher
      U36-2 (-) or U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  17. Click here

    INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  18. Click here

    INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  19. Click here

    INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  20. Click here

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

    3. Clear the DTCs.


      1. Body Electrical > Navigation System > Clear DTCs


    4. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

  21. Click here

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

    3. Clear the DTCs.


      1. Body Electrical > Navigation System > Clear DTCs


    4. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

  22. Click here

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. Inspect the rear No. 2 speaker assembly.

      Click here

    3. Clear the DTCs.


      1. Body Electrical > Navigation System > Clear DTCs


    4. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

  23. Click here

    REPLACE REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. Inspect the rear header speaker assembly.

      Click here

    3. Clear the DTCs.


      1. Body Electrical > Navigation System > Clear DTCs


    4. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END

    • NG

      REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLYClick here