Click here

AUDIO AND VISUAL SYSTEM(w/ Parking Assist Monitor System), Diagnostic DTC:B15C3

Click here
Click here
DTC Code DTC Name
B15C3 Speaker Output Short
Click here

DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C3 Speaker Output Short A short is detected in the speaker output circuit.

  • Harness or connector

  • Speaker

  • Stereo component amplifier assembly
B0066LPE04
Click here

WIRING DIAGRAM

Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    4. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    5. Disconnect the T23 and U34 rear header speaker assembly connectors.

    6. Disconnect the T24 rear No. 3 speaker assembly connector.

    7. Disconnect the O56 front No. 3 speaker assembly connector.

    8. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - Body ground Always 10 kΩ or higher
      T20-28 (FR-) - Body ground Always 10 kΩ or higher
      T20-12 (FL+) - Body ground Always 10 kΩ or higher
      T20-27 (FL-) - Body ground Always 10 kΩ or higher
      T20-5 (WFR+) - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) - Body ground Always 10 kΩ or higher
      T20-7 (CTR+) - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) - Body ground Always 10 kΩ or higher
      T20-15 (RR+) - Body ground Always 10 kΩ or higher
      T20-30 (RR-) - Body ground Always 10 kΩ or higher
      T20-14 (RL+) - Body ground Always 10 kΩ or higher
      T20-29 (RL-) - Body ground Always 10 kΩ or higher
      T20-11 (SR+) - Body ground Always 10 kΩ or higher
      T20-26 (SR-) - Body ground Always 10 kΩ or higher
      T20-10 (SL+) - Body ground Always 10 kΩ or higher
      T20-25 (SL-) - Body ground Always 10 kΩ or higher
      T20-6 (WF1+) - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  2. Click here

    CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY - BODY GROUND)


    1. Disconnect the T25 and U35 rear speaker assembly connectors.

    2. Disconnect the T26 and U36 rear No. 2 speaker assembly connectors.

    3. Measure the resistance between each of the rear speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T25-1 - Body ground Always 10 kΩ or higher
      T25-2- Body ground Always 10 kΩ or higher
      U35-1 - Body ground Always 10 kΩ or higher
      U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. Click here

    INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. B0065TNC23
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 6.5 to 9.7 Ω
      Result
      Proceed to
      OK
      NG

  4. Click here

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Replace the front No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Tip:

      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on the LH and RH sides.

      Result
      Proceed to
      OK
      NG

  5. Click here

    INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. B00654PC03
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 4.3 to 6.3 Ω
      Result
      Proceed to
      OK
      NG

  6. Click here

    INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. B0065TNC23
      *a

      Component without harness connected

      (Front No. 3 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 6.5 to 9.7 Ω
      Result
      Proceed to
      OK
      NG

  7. Click here

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY


    1. Replace the front No. 3 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

  8. Click here

    INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. B00654PC03
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.6 to 5.6 Ω
      Result
      Proceed to
      OK
      NG

  9. Click here

    INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. B0065HMC21
      *a

      Component without harness connected

      (Rear No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (+TW) - 1 (-TW) Always 10 kΩ or higher
      3 (+TW) - 4 (+) Always Below 1 Ω
      1 (-TW) - 2 (-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

  10. Click here

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Replace the rear No. 2 speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Tip:

      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on the LH and RH sides.

      Result
      Proceed to
      OK
      NG

  11. Click here

    INSPECT REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. B00684JC03
      *a

      Component without harness connected

      (Rear Header Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1(-) - 2(+) Always 6.5 to 9.7 Ω
      Result
      Proceed to
      OK
      NG

  12. Click here

    REPLACE REAR HEADER SPEAKER ASSEMBLY


    1. Replace the rear header speaker assembly with a new or known good one.

      Click here

    2. Clear the DTCs.

      Click here


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Tip:

      • Connect all the connectors to the rear header speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left rear header speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on the LH and RH sides.

      Result
      Proceed to
      OK
      NG

  13. Click here

    INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. B00654PC03
      *a

      Component without harness connected

      (Rear No. 3 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 4.8 to 6.8 Ω
      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLYClick here

    • NG

      REPLACE REAR NO. 3 SPEAKER ASSEMBLYClick here