Click here

AUDIO AND VISUAL SYSTEM(for 7 Inch Display) Display does not Dim when Light Control Switch is Turned ON

Click here
Click here
DTC Code DTC Name
  Display does not Dim when Light Control Switch is Turned ON
Click here

DESCRIPTION

When the audio and visual system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via AVC-LAN communication.

The radio receiver assembly switches between the daytime screen and night screen on the multi-display assembly according to the illumination signal input.

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

Click here

PROCEDURE


  1. Click here

    CHECK SYMPTOMS


    1. Check the symptoms that occur by viewing the display.

      Result
      Result Proceed to
      There is a delay until the display dims after the audio and visual system is activated with the light control switch in the tail or head position. A
      The display dims for a moment and then becomes bright after the audio and visual system is activated with the light control switch in the tail or head position. B
      When the light control switch is set to the tail or head position, the display dims but does not switch to the night screen.
      When the light control switch is set to the tail or head position, the display neither dims nor switches to the night screen. C
      Tip:

      • When the audio and visual system is activated with the light control switch in the tail or head position, before AVC-LAN communication is established, the multi-display assembly dims the display according to the illumination signal received via a direct line.

      • After AVC-LAN communication is established, the multi-display assembly dims the display according to a dimmer signal sent via a direct line.

      • The radio receiver assembly switches between the daytime screen and night screen on the multi-display assembly according to the illumination signal input.


  2. Click here

    CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)


    1. Disconnect the O60 multi-display assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O60-13 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O60-2 (ILL) - O60-13 (GND1) Light control switch in tail or head position 11 to 14 V
      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. Click here

    CHECK IMAGE QUALITY SETTING


    1. Turn the light control switch to the tail or head position.

    2. Check that the daytime screen setting on the display adjustment screen is set to on.

      Result
      Result Proceed to
      Daytime screen setting is set to on. A
      Daytime screen setting is set to off. B

    • A

      CHANGE DAYTIME SCREEN SETTING TO OFF

    • BClick here
  4. Click here

    CHECK VEHICLE SIGNAL (OPERATION CHECK)


    1. B006688

      Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

      Click here

    2. Check that the display changes between ON and OFF according to the light control switch operation.

      OK
      Light Control Switch Display
      Tail or head ON
      Off or AUTO OFF
      Tip:

      • This display is updated once per second. As a result, it is normal for the display to lag behind the actual switch operation.

      • Make sure to move the vehicle to a bright area before performing an operation check with the light control switch in the AUTO position.

      Result
      Proceed to
      OK
      NG

  5. Click here

    CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)


    1. Disconnect the O147 and O146 radio receiver assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O146-1 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O147-15 (ILL+) - O146-1 (GND1) Light control switch in tail or head position 11 to 14 V
      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR