Click here

AUDIO AND VISUAL SYSTEM(for 10.3 Inch Display), Diagnostic DTC:B15D6

Click here
Click here
DTC Code DTC Name
B15D6 Display Disconnected
Click here

DESCRIPTION

The multi-display assembly and radio receiver assembly are connected via AVC-LAN communication lines.

This DTC is stored when an AVC-LAN communication error occurs between the multi-display assembly and radio receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D6 Display Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing.

  • Multi-display assembly power source circuit

  • AVC-LAN circuit between radio receiver assembly and multi-display assembly

  • Multi-display assembly

  • Radio receiver assembly

  • Harness or connector
Tip:

The radio receiver assembly is the master unit.

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

    Click here

  • When replacing the radio receiver assembly, always replace it with a new one. If a radio receiver assembly which was installed to another vehicle is used, the following may occur:


    • A communication malfunction DTC may be stored.

    • The radio receiver assembly may not operate normally.

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Click here

PROCEDURE


  1. Click here

    CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check for optional components.


      1. Check that optional components (including associated wiring) which generate radio waves are not installed.

        Result
        Result Proceed to
        Optional components (including associated wiring) are installed. A
        Optional components (including associated wiring) are not installed. B
        Tip:

        • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

        • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


  2. Click here

    REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note:

      Do not remove optional components or associated wiring without the permission of the customer.

      Result
      Proceed to
      NEXT

  3. Click here

    CHECK DTC


    1. Clear the DTCs.


      1. Body Electrical > Navigation System > Clear DTCs


    2. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

  4. Click here

    CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY POWER SOURCE)


    1. Disconnect the O60 multi-display assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O60-13 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O60-12 (B) - O60-13 (GND1) Always 11 to 14 V
      O60-24 (ACC) - O60-13 (GND1) Engine switch on (ACC) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. Click here

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)


    1. Disconnect the O146 radio receiver assembly connector.

    2. Disconnect the O60 multi-display assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O146-5 (TX1+) - O60-7 (TX+) Always Below 1 Ω
      O146-6 (TX1-) - O60-19 (TX-) Always Below 1 Ω
      O146-5 (TX1+) or O60-7 (TX+) - Body ground Always 10 kΩ or higher
      O146-6 (TX1-) or O60-19 (TX-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    REPLACE MULTI-DISPLAY ASSEMBLY


    1. Replace the multi-display assembly with a new or known good one.

      Click here

    2. Clear the DTCs.


      1. Body Electrical > Navigation System > Clear DTCs


    3. Recheck for DTCs and check that no DTCs are output.


      1. Body Electrical > Navigation System > Trouble Codes


      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    • OK

      END

    • NG

      REPLACE RADIO RECEIVER ASSEMBLYClick here