Click here

AUDIO AND VISUAL SYSTEM(w/o Parallel Parking Assist Function) Speaker Circuit

Click here
Click here
DTC Code DTC Name
  Speaker Circuit
Click here

DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly*1 or speakers.

*1: for 10 Speakers

Click here

WIRING DIAGRAM


Click here
  1. A01VO41E04

    for 6 Speakers

  2. A01VO22E15
    B0067O6E07

    for 10 Speakers

Click here

PROCEDURE


  1. Click here

    CONFIRM MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 6 Speakers A
      for 10 Speakers B

  2. Click here

    CHECK SPEAKER (OPERATION CHECK)


    1. A01VMY1

      Enter the "System Check Mode" screen. Refer to Check Seaker in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not operating speaker Proceed to
      Front No. 1 speaker assembly A
      Front No. 2 speaker assembly B
      Rear speaker assembly C
      Tip:

      If sound cannot be heard from any speaker, inspect all of them.


  3. Click here

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the O68 radio receiver assembly connector.

    2. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O68-1 (FR+) - R14-1 Always Below 1 Ω
      O68-5 (FR-) - R14-2 Always Below 1 Ω
      O68-2 (FL+) - S14-1 Always Below 1 Ω
      O68-6 (FL-) - S14-2 Always Below 1 Ω
      O68-1 (FR+) or R14-1 - Body ground Always 10 kΩ or higher
      O68-5 (FR-) or R14-2 - Body ground Always 10 kΩ or higher
      O68-2 (FL+) or S14-1 - Body ground Always 10 kΩ or higher
      O68-6 (FL-) or S14-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  4. Click here

    INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPLACE FRONT NO. 1 SPEAKER ASSEMBLYClick here

  5. Click here

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - RADIO SETTING CONDENSER - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the O68 radio receiver assembly connector.

    2. Disconnect the O67 radio setting condenser connector.

    3. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O68-1 (FR+) - O67-3 (RIN) Always Below 1 Ω
      O68-5 (FR-) - O67-6 (ROUT) Always Below 1 Ω
      O68-2 (FL+) - O67-1 (LIN) Always Below 1 Ω
      O68-6 (FL-) - O67-2 (LOUT) Always Below 1 Ω
      O67-8 (RI+) - O54-2 Always Below 1 Ω
      O67-7 (RI-) - O54-1 Always Below 1 Ω
      O67-4 (LI+) - O55-2 Always Below 1 Ω
      O67-5 (LI-) - O55-1 Always Below 1 Ω
      O68-1 (FR+) or O67-3 (RIN) - Body ground Always 10 kΩ or higher
      O68-5 (FR-) or O67-6 (ROUT) - Body ground Always 10 kΩ or higher
      O68-2 (FL+) or O67-1 (LIN) - Body ground Always 10 kΩ or higher
      O68-6 (FL-) or O67-2 (LOUT) - Body ground Always 10 kΩ or higher
      O67-7 (RI-) or O54-1 - Body ground Always 10 kΩ or higher
      O67-8 (RI+) or O54-2 - Body ground Always 10 kΩ or higher
      O67-5 (LI-) or O55-1 - Body ground Always 10 kΩ or higher
      O67-4 (LI+) or O55-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  7. Click here

    REPLACE RADIO SETTING CONDENSER


    1. Check that the malfunction disappears when a new or known good radio setting condenser is installed.

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    • OK

      END

    • NG

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

  8. Click here

    CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the O69 radio receiver assembly connector.

    2. Disconnect the T25 and U35 rear speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O69-1 (RR+) - T25-1 Always Below 1 Ω
      O69-3 (RR-) - T25-2 Always Below 1 Ω
      O69-2 (RL+) - U35-1 Always Below 1 Ω
      O69-6 (RL-) - U35-2 Always Below 1 Ω
      O69-1 (RR+) or T25-1 - Body ground Always 10 kΩ or higher
      O69-3 (RR-) or T25-2 - Body ground Always 10 kΩ or higher
      O69-2 (RL+) or U35-1 - Body ground Always 10 kΩ or higher
      O69-6 (RL-) or U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPLACE REAR SPEAKER ASSEMBLYClick here

  10. Click here

    CHECK SPEAKER (OPERATION CHECK)


    1. A01VMY1

      Enter the "System Check Mode" screen. Refer to Check SP Check On in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not operating speaker Proceed to
      Front No. 2 speaker assembly A
      Front No. 1 speaker assembly B
      Rear speaker assembly C
      Rear No. 3 speaker assembly D
      Front No. 3 speaker assembly E
      Tip:

      If sound cannot be heard from any speaker, inspect all of them.


  11. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O54 and O55 front No. 2 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-13 (FR+) - O54-2 Always Below 1 Ω
      T20-28 (FR-) - O54-1 Always Below 1 Ω
      T20-12 (FL+) - O55-2 Always Below 1 Ω
      T20-27 (FL-) - O55-1 Always Below 1 Ω
      T20-13 (FR+) or O54-2 - Body ground Always 10 kΩ or higher
      T20-28 (FR-) or O54-1 - Body ground Always 10 kΩ or higher
      T20-12 (FL+) or O55-2 - Body ground Always 10 kΩ or higher
      T20-27 (FL-) or O55-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. Click here

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. Inspect the front No. 2 speaker assembly.

      Click here

      OK
      Malfunction disappears.
      Result
      Proceed to
      OK
      NG

    • OK

      END

    • NG

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

  13. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the R14 and S14 front No. 1 speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-5 (WFR+) - R14-1 Always Below 1 Ω
      T20-20 (WFR-) - R14-2 Always Below 1 Ω
      T20-4 (WFL+) - S14-1 Always Below 1 Ω
      T20-19 (WFL-) - S14-2 Always Below 1 Ω
      T20-5 (WFR+) or R14-1 - Body ground Always 10 kΩ or higher
      T20-20 (WFR-) or R14-2 - Body ground Always 10 kΩ or higher
      T20-4 (WFL+) or S14-1 - Body ground Always 10 kΩ or higher
      T20-19 (WFL-) or S14-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  14. Click here

    INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. Inspect the front No. 1 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPLACE FRONT NO. 1 SPEAKER ASSEMBLYClick here

  15. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T25 and U35 rear speaker assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-15 (RR+) - T25-1 Always Below 1 Ω
      T20-30 (RR-) - T25-2 Always Below 1 Ω
      T20-14 (RL+) - U35-1 Always Below 1 Ω
      T20-29 (RL-) - U35-2 Always Below 1 Ω
      T20-15 (RR+) or T25-1 - Body ground Always 10 kΩ or higher
      T20-30 (RR-) or T25-2 - Body ground Always 10 kΩ or higher
      T20-14 (RL+) or U35-1 - Body ground Always 10 kΩ or higher
      T20-29 (RL-) or U35-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  16. Click here

    INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. Inspect the rear speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPLACE REAR SPEAKER ASSEMBLYClick here

  17. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the T24 rear No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-6 (WF1+) - T24-1 Always Below 1 Ω
      T20-21 (WF1-) - T24-2 Always Below 1 Ω
      T20-6 (WF1+) or T24-1 - Body ground Always 10 kΩ or higher
      T20-21 (WF1-) or T24-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  18. Click here

    INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. Inspect the rear No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPLACE REAR NO. 3 SPEAKER ASSEMBLYClick here

  19. Click here

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the T20 stereo component amplifier assembly connector.

    2. Disconnect the O56 front No. 3 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      T20-7 (CTR+) - O56-2 Always Below 1 Ω
      T20-22 (CTR-) - O56-1 Always Below 1 Ω
      T20-7 (CTR+) or O56-2 - Body ground Always 10 kΩ or higher
      T20-22 (CTR-) or O56-1 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  20. Click here

    INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. Inspect the front No. 3 speaker assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    • OK

      PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLEClick here

    • NG

      REPLACE FRONT NO. 3 SPEAKER ASSEMBLYClick here