STEERING COLUMN ASSEMBLY INSTALLATION

PROCEDURE

1. Click here

   INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

   
   
   1. 

      *a

      Matchmark

      Connect the steering sliding yoke sub-assembly to the No. 2 steering intermediate shaft assembly.

      Note:

      Align the matchmarks on the steering sliding yoke sub-assembly and No. 2 steering intermediate shaft assembly.

   2. Temporarily install the bolt.

2. Click here

   ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

3. Click here

   INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

   
   
   1. 

      *a

      Matchmark

      Install the steering sliding yoke sub-assembly with No. 2 steering intermediate shaft assembly to the power steering link assembly.

      Note:

      Align the matchmarks on the steering sliding yoke sub-assembly and power steering link assembly.

   2. 

      Install the bolt.

      35.3 N*m

      360 kgf*cm

      26 ft.*lbf

   3. Tighten the clamp.

4. Click here

   INSTALL STEERING COLUMN ASSEMBLY

   
   
   1. 

      *a

      Matchmark

      Install the steering column assembly to the No. 2 steering intermediate shaft assembly.

      Note:

      Align the matchmarks on the steering column assembly and No. 2 steering intermediate shaft assembly.

   2. Install the steering column assembly with the 4 nuts.

      25.5 N*m

      260 kgf*cm

      19 ft.*lbf

   3. 

      Install the bolt.

      35.3 N*m

      360 kgf*cm

      26 ft.*lbf

   4. Install the brake pedal return spring to the push rod pin and steering column assembly.

   5. Connect each connector and engage each wire harness clamp to the steering column assembly.

   6. 

      Fully tighten the bolt.

      35.3 N*m

      360 kgf*cm

      26 ft.*lbf

5. Click here

   INSTALL FRONT SUSPENSION MEMBER BRACE SUB-ASSEMBLY

   Click here

6. Click here

   INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for LHD)

   
   

   1. Install the No. 1 air duct sub-assembly with the bolt.

      9.8 N*m

      100 kgf*cm

      87 in.*lbf

7. Click here

   INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY (for RHD)

   Tip:

   Use the same procedure as for the No. 1 air duct sub-assembly.

8. Click here

   INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

   Click here

9. Click here

   INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

   Note:
   

   • Do not replace the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

   • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).

   • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

   
   

   1. Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

   2. Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.

10. Click here

    INSTALL STEERING COLUMN COVER

    
    

    1. Engage the 2 claws to install the steering column cover (upper).

    2. Engage the 6 clips to the steering column cover (upper).

    3. Engage the 2 claws to install the steering column cover (lower).

    4. Install the 3 screws.

11. Click here

    ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

12. Click here

    INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Click here

13. Click here

    INSTALL STEERING WHEEL ASSEMBLY

    w/ Lane Departure Alert System:Click here

    w/o Lane Departure Alert System:Click here

14. Click here

    CHECK STEERING WHEEL CENTER POINT

15. Click here

    INSTALL HORN BUTTON ASSEMBLY

    Click here

16. Click here

    CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

    
    

    1. Reset the auto tilt away function setting to the previous condition by changing the customize parameter.

       Click here

17. Click here

    ADJUST PARKING ASSIST MONITOR SYSTEM (w/ Parking Assist Monitor System)

    Click here