Click here

REAR SUSPENSION MEMBER REMOVAL

Click here
Click here Click here

PROCEDURE


  1. Click here

    REMOVE REAR WHEEL

    Click here

  2. Click here

    REMOVE FRONT CENTER FLOOR COVER LH


    1. B00658UN01

      Remove the 4 clips (A) and clip (B).

    2. Disengage the 5 clamps and remove the front center floor cover LH.

  3. Click here

    REMOVE FRONT CENTER FLOOR COVER RH

    Tip:

    Perform the same procedure as for the LH side.

  4. Click here

    REMOVE NO. 1 FLOOR UNDER COVER ASSEMBLY


    1. B006744

      Disconnect the 5 grommets and remove the 4 clips and No. 1 floor under cover assembly.

  5. Click here

    REMOVE FRONT CENTER FLOOR BRACE


    1. B00654R

      Remove the 6 bolts and 2 nuts.

    2. Disengage the 2 clips and remove the front center floor brace.

  6. Click here

    REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

    Click here

  7. Click here

    DISCONNECT TAIL EXHAUST PIPE LH

    Click here

  8. Click here

    DISCONNECT TAIL EXHAUST PIPE ASSEMBLY

    Click here

  9. Click here

    REMOVE REAR SUSPENSION ARM COVER LH

    Click here

  10. Click here

    REMOVE REAR SUSPENSION ARM COVER RH

    Tip:

    Perform the same procedure as for the LH side.

  11. Click here

    REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

    Click here

  12. Click here

    REMOVE REAR AXLE SHAFT NUT LH

    Click here

  13. Click here

    REMOVE REAR AXLE SHAFT NUT RH

    Tip:

    Perform the same procedure as for the LH side.

  14. Click here

    SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH

    Click here

  15. Click here

    SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  16. Click here

    REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG


    1. Remove the 2 parking brake shoe adjusting hole plugs.

  17. Click here

    REMOVE REAR DISC LH

    Click here

  18. Click here

    REMOVE REAR DISC RH

    Tip:

    Perform the same procedure as for the LH side.

  19. Click here

    REMOVE PARKING BRAKE ASSEMBLY (for LH Side)

    Click here

  20. Click here

    REMOVE PARKING BRAKE ASSEMBLY (for RH Side)

    Tip:

    Perform the same procedure as for the LH side.

  21. Click here

    SEPARATE REAR SPEED SENSOR LH

    Click here

  22. Click here

    SEPARATE REAR SPEED SENSOR RH

    Tip:

    Perform the same procedure as for the LH side.

  23. Click here

    SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    1. B0067C1

      Remove the 2 bolts and separate the No. 3 parking brake cable assembly from the rear suspension member sub-assembly.

  24. Click here

    SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

    Tip:

    Perform the same procedure as for the No. 3 parking brake cable assembly.

  25. Click here

    SEPARATE REAR STEERING TIE ROD ASSEMBLY LH

    Click here

  26. Click here

    SEPARATE REAR STEERING TIE ROD ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  27. Click here

    REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  28. Click here

    REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  29. Click here

    REMOVE REAR STABILIZER LINK ASSEMBLY LH

    Click here

  30. Click here

    REMOVE REAR STABILIZER LINK ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  31. Click here

    SEPARATE REAR SHOCK ABSORBER ASSEMBLY LH

    Click here

  32. Click here

    SEPARATE REAR SHOCK ABSORBER ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  33. Click here

    REMOVE REAR SUSPENSION MEMBER BRACE LH

    Click here

  34. Click here

    REMOVE REAR SUSPENSION MEMBER BRACE RH

    Tip:

    Perform the same procedure as for the LH side.

  35. Click here

    REMOVE REAR COIL SPRING LH

    Click here

  36. Click here

    REMOVE REAR COIL SPRING RH

    Tip:

    Perform the same procedure as for the LH side.

  37. Click here

    REMOVE REAR UPPER COIL SPRING INSULATOR LH

    Click here

  38. Click here

    REMOVE REAR UPPER COIL SPRING INSULATOR RH

    Tip:

    Perform the same procedure as for the LH side.

  39. Click here

    REMOVE REAR LOWER COIL SPRING INSULATOR LH

    Click here

  40. Click here

    REMOVE REAR LOWER COIL SPRING INSULATOR RH

    Tip:

    Perform the same procedure as for the LH side.

  41. Click here

    REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  42. Click here

    REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  43. Click here

    SEPARATE REAR NO. 1 UPPER CONTROL ARM ASSEMBLY LH


    1. A01OG45

      Remove the bolt, nut and washer and separate the rear No. 1 upper control arm assembly LH from the rear axle assembly.

      Note:

      Because the bolt has its own stopper, do not turn the bolt. Loosen the nut with the bolt secured.

  44. Click here

    SEPARATE REAR NO. 1 UPPER CONTROL ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  45. Click here

    LOOSEN REAR NO. 2 UPPER CONTROL ARM ASSEMBLY LH


    1. B0066X2

      Remove the bolt and separate the rear speed sensor LH from the rear No. 2 upper control arm assembly LH.

    2. B00652F

      Loosen the rear No. 2 upper control arm assembly LH nut (rear axle assembly side).

      Note:

      • Do not remove the bolt and nut.

      • Because the bolt has its own stopper, do not turn the bolt. Loosen the nut with the bolt secured.

  46. Click here

    LOOSEN REAR NO. 2 UPPER CONTROL ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  47. Click here

    REMOVE REAR AXLE ASSEMBLY LH

    Click here

  48. Click here

    REMOVE REAR AXLE ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  49. Click here

    REMOVE REAR DRIVE SHAFT ASSEMBLY LH

    Click here

  50. Click here

    REMOVE REAR DRIVE SHAFT ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

  51. Click here

    REMOVE REAR BODY MOUNTING CUSHION SUB-ASSEMBLY LH


    1. B0066UC

      Remove the 4 bolts and rear body mounting cushion sub-assembly LH.

  52. Click here

    REMOVE REAR BODY MOUNTING CUSHION SUB-ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  53. Click here

    DISCONNECT NO. 4 FLOOR WIRE (for Torque Vectoring Differential)

    Click here

  54. Click here

    REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. B0065BWC01
      *a Engine Lifter
      *b Attachment
      B00667M Attachment placement location

      Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

      CAUTION:

      Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

      Note:

      • Use attachments to keep the rear suspension member sub-assembly level.

      • The rear suspension member sub-assembly is a heavy component. Make sure that it is supported securely.

    2. Remove the 12 bolts, rear floor panel brace sub-assembly LH, rear floor panel brace sub-assembly RH, rear suspension member lower stopper sub-assembly LH and rear suspension member lower stopper sub-assembly RH.

    3. Slowly lower the rear suspension member sub-assembly.

      Note:

      When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.

  55. Click here

    REMOVE NO. 4 FLOOR WIRE (for Torque Vectoring Differential)

    Click here

  56. Click here

    REMOVE REAR SUSPENSION ARM BRACKET ASSEMBLY

    Click here

  57. Click here

    REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY (for LSD)

    Click here

  58. Click here

    REMOVE TORQUE VECTORING DIFFERENTIAL FDU (FINAL DRIVE UNIT) (for Torque Vectoring Differential)

    Click here

  59. Click here

    REMOVE REAR STABILIZER BAR SUB-ASSEMBLY


    1. B0066IG

      Remove the 4 bolts and rear stabilizer bar sub-assembly with 2 rear No. 1 stabilizer bar brackets from the rear suspension member sub-assembly.

  60. Click here

    REMOVE REAR NO. 1 UPPER CONTROL ARM ASSEMBLY LH

    Click here

  61. Click here

    REMOVE REAR NO. 1 UPPER CONTROL ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  62. Click here

    REMOVE REAR NO. 2 UPPER CONTROL ARM ASSEMBLY LH

    Click here

  63. Click here

    REMOVE REAR NO. 2 UPPER CONTROL ARM ASSEMBLY RH

    Tip:

    Perform the same procedure as for the LH side.

  64. Click here

    REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

    Click here

  65. Click here

    REMOVE REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

    Click here

  66. Click here

    REMOVE REAR SUSPENSION MEMBER REAR LOWER STOPPER (for LH Side)


    1. B0066IX

      Remove the rear suspension member rear lower stopper from the rear suspension member sub-assembly.

  67. Click here

    REMOVE REAR SUSPENSION MEMBER REAR LOWER STOPPER (for RH Side)

    Tip:

    Perform the same procedure as for the LH side.

  68. Click here

    REMOVE REAR SUSPENSION MEMBER REAR UPPER STOPPER (for LH Side)


    1. B00667F

      Remove the rear suspension member rear upper stopper from the rear suspension member sub-assembly.

  69. Click here

    REMOVE REAR SUSPENSION MEMBER REAR UPPER STOPPER (for RH Side)

    Tip:

    Perform the same procedure as for the LH side.

  70. Click here

    REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)


    1. B0067BV

      Using a chisel and hammer, bend the rear suspension member front body mounting cushion rib.

    2. B006692C03
      *a Turn
      *b Hold

      Using SST, remove the rear suspension member front body mounting cushion while applying grease into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.

      09950-40011 09951-04020 09952-04010 09953-04030 09954-04010 09955-04051 09957-04010 09958-04011
      09950-60010 09951-00410
      Note:

      • Apply grease to the threads and tip of the SST center bolt before use.

      • Be careful as the rear suspension member front body mounting cushion may fly out.

      • The rear suspension member front body mounting cushion cannot be reused.

  71. Click here

    REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

    Tip:

    Perform the same procedure as for the LH side.

  72. Click here

    REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for LH Side)


    1. B0067WFC03
      *a Turn
      *b Hold

      Using SST, remove the rear suspension member rear body mounting cushion while applying grease into the clearance between the rear suspension member rear body mounting cushion and the rear suspension member sub-assembly.

      09950-00020
      09950-00030
      09950-40011 09957-04010
      09950-60010 09951-00390
      Note:

      • Apply grease to the threads and tip of the SST center bolt before use.

      • Be careful as the rear suspension member rear body mounting cushion may fly out.

      • The rear suspension member rear body mounting cushion cannot be reused.

  73. Click here

    REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for RH Side)

    Tip:

    Perform the same procedure as for the LH side.