COMBINATION SWITCH INSPECTION

PROCEDURE

1. Click here

   INSPECT COMBINATION SWITCH ASSEMBLY

   
   

   1. Inspect the ECO drive mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 11 (ECO) - 16 (E) Combination switch turned and held at ECO position Below 50 Ω Combination switch not turned 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   2. Inspect the NORMAL mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 9 (NORM) - 16 (E) Combination switch pushed and held Below 50 Ω Combination switch not pushed 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   3. Inspect the SPORT or SPORT S/S+ mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 10 (PWR) - 16 (E) Combination switch turned and held at SPORT or SPORT S/S+ position Below 50 Ω Combination switch not turned 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   4. Inspect the SNOW mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 3 (SNSW) - 16 (E) SNOW mode switch pushed and held Below 50 Ω SNOW mode switch not pushed 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   5. Inspect the VSC off mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 1 (+) - 16 (E) VSC OFF mode switch pushed and held Below 50 Ω VSC OFF mode switch not pushed 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   6. Inspect the TVD mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 2 (TVD) - 16 (E) TVD mode switch pushed and held Below 50 Ω TVD mode switch not pushed 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   7. Check the illumination (w/ Torque Vectoring Differential Carrier Assembly):

      
      
      1. 

         *A	w/ Snow Switch
         *B	w/o Snow Switch
         *a	Component without harness connected (Combination Switch Assembly)
         *b	Combination Switch Assembly Illumination

         Apply battery voltage to the combination switch assembly and check that the combination switch assembly illuminates.

         Standard
         Measurement Condition Specified Condition Battery positive (+) → 5 (ILL+) Battery negative (-) → 8 (ILL-) Illuminates

         If the result is not as specified, replace the combination switch assembly.

   8. Check the illumination (w/o Torque Vectoring Differential Carrier Assembly):

      
      
      1. 

         *A	w/ Snow Switch
         *B	w/o Snow Switch
         *a	Component without harness connected (Combination Switch Assembly)
         *b	Combination Switch Assembly Illumination

         Apply battery voltage to the combination switch assembly and check that the combination switch assembly illuminates.

         Standard
         Measurement Condition Specified Condition Battery positive (+) → 5 (ILL+) Battery negative (-) → 8 (ILL-) Illuminates

         If the result is not as specified, replace the combination switch assembly.