REAR SPEED SENSOR REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

  • The rear speed sensor rotor is a component of the rear axle hub and bearing assembly. If the rear speed sensor rotor is malfunctioning, replace the rear axle hub and bearing assembly.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Spare Tire)

    Click here

  4. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/ Spare Tire)

    Click here

  5. REMOVE SPARE WHEEL COVER TRAY (w/o Spare Tire)

    Click here

  6. REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER

    Click here

  7. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  8. REMOVE FRONT UPPER LUGGAGE COMPARTMENT TRIM COVER

    Click here

  9. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER

    Click here

  10. SEPARATE LUGGAGE COMPARTMENT TRIM COVER LH (for LH Side)


    1. B00658I

      Disengage the 4 claws and open the 2 covers.

    2. B00654U

      Remove the 2 bolts and 2 rope hook assemblies.

    3. B00670S

      Remove the 4 clips.

    4. Disengage the claw.

    5. Separate the luggage compartment trim cover LH from the vehicle body.

  11. SEPARATE LUGGAGE COMPARTMENT TRIM COVER RH (for RH Side)


    1. B0067Q7

      Disengage the 4 claws and open the 2 covers.

    2. B006659

      Remove the 2 bolts and 2 rope hook assemblies.

    3. w/o Deck Side Trim Box:


      1. B0067ZU

        Remove the 4 clips.

      2. Disengage the claw.

      3. Separate the luggage compartment trim cover RH from the vehicle body.

    4. w/ Deck Side Trim Box:


      1. B006622

        Disengage the clip and 5 guides and remove the deck side trim box RH.

      2. B0065C5

        Remove the 4 clips.

      3. Disengage the claw.

      4. Separate the luggage compartment trim cover RH from the vehicle body.

  12. REMOVE REAR WHEEL

    Click here

  13. SEPARATE REAR WHEEL HOUSE LINER


    1. B00680X

      Remove the 2 nuts and separate the rear wheel house liner.

  14. REMOVE REAR SPEED SENSOR


    1. Turn back the luggage compartment trim cover until the rear speed sensor connector can be seen.

    2. Disengage the rear speed sensor connector.

      B0066DCC01
      *A for LH Side *B for RH Side
    3. B0067GNC01
      *1 Pad Wear Indicator Wire
      *2 Rear Speed Sensor

      Disconnect the pad wear indicator wire connector from the rear speed sensor.

    4. Remove the 3 bolts and separate the rear speed sensor and 2 sensor clamps from the rear axle carrier sub-assembly and rear No. 2 upper control arm assembly.

      Note


      • Prevent foreign matter from attaching to the rear speed sensor tip.

      • Clean the speed sensor installation hole and the contact surfaces every time the rear speed sensor is removed.

    5. Turn back the rear wheel house liner until the grommet can be disengaged.

    6. B00661E

      Remove the 2 nuts and 2 sensor clamps.

    7. Disengage the grommet and remove the rear speed sensor.