VEHICLE STABILITY CONTROL SYSTEM, Diagnostic DTC:U0073, U0100, U0124, U0126, U110F

DTC Code DTC Name
U0073 Control Module Communication Bus Off
U0100 Lost Communication With ECM/PCM "A"
U0124 Lost Communication With Lateral Acceleration Sensor Module
U0126 Lost Communication With Steering Angle Sensor Module
U110F Lost Communication With Roll Rate Sensor/Vertical Acceleration Sensor Module

DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the ECM, steering angle sensor, yaw rate and acceleration sensor and roll rate and vertical acceleration sensor (yaw rate sensor) via CAN communication.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0073 Control Module Communication Bus Off

Any of the following is detected:


  1. A bus OFF state occurs once or more within 0.1 seconds, 10 times in succession. (Sent signals cannot be received.)

  2. When the +BS terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate and acceleration sensor and steering angle sensor continues for 1 second or more.

  3. When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds:


    • A delay in receiving data from the yaw rate and acceleration sensor and steering angle sensor occurs more than once within 5 seconds.

 CAN communication system
U0100 Lost Communication With ECM/PCM "A" When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received from the ECM for 2 seconds or more.

  • CAN communication system

  • Skid control ECU (brake actuator assembly)

  • ECM
U0124 Lost Communication With Lateral Acceleration Sensor Module

Either of the following is detected:


  1. When the +BS terminal voltage is between 10 and 17.4 V, and the vehicle speed is 7 km/h (4 mph) or more, data from the acceleration sensor cannot be received for 1 second or more.

  2. When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession within 60 seconds.


    • The condition that data from the acceleration sensor cannot be received occurs once or more within 5 seconds.

  • CAN communication system

  • Skid control ECU (brake actuator assembly)

  • Acceleration sensor (yaw rate and acceleration sensor)
U0126 Lost Communication With Steering Angle Sensor Module

Either of the following is detected:


  1. When the +BS terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more.

  2. When the +BS terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession.


    • The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds.

  • CAN communication system

  • Skid control ECU (brake actuator assembly)

  • Steering angle sensor
U110F Lost Communication With Roll Rate Sensor/Vertical Acceleration Sensor Module The +BS terminal voltage is between 10 and 17.4 V and data cannot be received from the roll rate and vertical acceleration sensor once or more within 5 seconds 10 times consecutively in 60 seconds.

  • CAN communication system

  • Skid control ECU (brake actuator assembly)

  • Roll rate and vertical acceleration sensor (yaw rate sensor)

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)


    1. Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

      Click here


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      EFI Communication Open ECM communication open detection Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -
      Yaw Rate Open Yaw rate sensor open detection Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -
      Deceleration Open Acceleration sensor open detection Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -
      Steering Open Steering angle sensor open detection Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -
      Vertical Acceleration Sensor Open Momentary interruption (open circuit) status in the wire harness between the skid control ECU (brake actuator assembly) and the roll rate and vertical acceleration sensor (yaw rate sensor) Error or Normal

      Error: Momentary interruption

      Normal: Normal

      		 -

      Chassis > ABS/VSC/TRC > Data List
      Tester Display
      EFI Communication Open
      Yaw Rate Open
      Deceleration Open
      Steering Open
      Vertical Acceleration Sensor Open
      Result
      Result Proceed to
      There is a constant open circuit. A
      There are no momentary interruptions. B
      There are momentary interruptions. C

      Tech Tips

      Perform the above inspection before disconnecting any sensors or connectors.


    B

    GO TO STEP 3 Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    A

  2. CHECK IF EACH CONNECTOR IS SECURELY CONNECTED (ECM, SENSOR)


    1. Turn the engine switch off.

    2. Check if each sensor and ECM connector is securely connected.

      OK
      Each connector is securely connected.
      Result
      Proceed to
      OK
      NG

    NG

    CONNECT CONNECTOR TO EACH SENSOR OR ECM CORRECTLY

    OK

  3. RECONFIRM DTC


    1. Turn the engine switch off.

    2. Record the output DTCs (for VSC system and/or CAN communication system).

      for VSC system: Click here

      for CAN communication system: Click here


      Chassis > ABS/VSC/TRC > Trouble Codes

      Tech Tips

      If CAN communication system DTCs and related sensor DTCs are output simultaneously, troubleshoot the DTCs (for VSC system) after the CAN communication system returns to normal.

      Result
      Result Proceed to
      DTCs are not output. A
      DTCs are output (relating to VSC system). B
      DTCs are output (relating to CAN communication system). C

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPAIR CIRCUITS INDICATED BY OUTPUT DTCS Click here

    C

    INSPECT CAN COMMUNICATION SYSTEM Click here

  4. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Turn the engine switch off.

    2. Repair or replace the harness or connector.

    3. Check for any momentary interruptions between the skid control ECU (brake actuator assembly) and each sensor or ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  5. RECONFIRM DTC


    1. Turn the engine switch off.

    2. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    3. Turn the engine switch off.

    4. Start the engine.

    5. Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.

    6. Check that no CAN communication system DTCs are output.

      Click here

    7. If VSC system DTCs are output, record them.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output. A
      DTCs are output (relating to VSC system). B
      DTCs are output (relating to CAN communication system). C

      Tech Tips

      The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for VSC system).


    A

    END

    B

    REPAIR CIRCUITS INDICATED BY OUTPUT DTCS Click here

    C

    INSPECT CAN COMMUNICATION SYSTEM Click here