Click here

SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P0617

Click here
Click here Click here
DTC Code DTC Name
P0617 Starter Relay Circuit High
Click here

MONITOR DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High

All of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):


  • (a) The vehicle speed is 20 km/h (12.43 mph) or more.

  • (b) The engine speed is 1000 rpm or higher.

  • (c) The STA signal is on.

  • Starter signal circuit

  • Park/Neutral position switch assembly

  • Certification ECU (smart key ECU assembly)

  • ECM

 Comes on DTC stored
Click here

MONITOR STRATEGY

Required Sensors/Components (Main)

ST relay

Park/Neutral position switch assembly

Certification ECU (smart key ECU assembly)
Required Sensors/Components (Related)

Vehicle speed sensor

Crankshaft position sensor
Frequency of Operation Continuous
Click here

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or higher
Click here

TYPICAL MALFUNCTION THRESHOLDS

Starter signal On
Click here

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on [A].

  6. Start the engine.

  7. Idle the engine for 5 seconds or more [B].

  8. Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [D].

  10. Read the pending DTCs.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P0617.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Tip:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS (STARTER SIGNAL)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.


      1. Powertrain > Engine > Data List
        Tester Display
        Starter Signal




    5. Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

      Result
      Condition Starter signal Proceed to
      Driving at 20 km/h (12.4 mph) or more OFF A
      ON B

  2. Click here

    INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. Inspect the park/neutral position switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

  3. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)


    1. Repair or replace harness or connector (park/neutral position switch assembly - ST relay - ECM - TCM - certification ECU (smart key ECU assembly)).

      Result
      Proceed to
      NEXT

  4. Click here

    CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here


      1. Powertrain > Engine > Clear DTCs


    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    7. Enter the following menus: Powertrain / Engine / Trouble Codes.

    8. Read the DTCs.


      1. Powertrain > Engine > Trouble Codes


      Result
      Result Proceed to
      DTC P0617 is output A
      DTCs are not output B

  5. Click here

    CHECK ENTRY AND START SYSTEM (STA SIGNAL)


    1. Check the entry and start system (for start function).

      Click here

      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE ECMClick here

    • NG

      REPAIR OR REPLACE ENTRY AND START SYSTEM