Click here

SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P0560

Click here
Click here Click here
DTC Code DTC Name
P0560 System Voltage
Click here

MONITOR DESCRIPTION

The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage An open in the ECM back up power source circuit (1 trip detection logic).

  • Open in back up power source circuit

  • Battery

  • Battery terminals

  • ECM

 Comes on DTC stored
Tip:

If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partially cleared.

Click here

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous
Click here

TYPICAL MALFUNCTION THRESHOLDS

Both of the following conditions are met -
Stand-by RAM Initialized
Continuous battery voltage Less than 3.5 V
Click here

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Wait 5 seconds or more.

  7. Enter the following menus: Powertrain / Engine / Trouble Codes.

  8. Read the pending DTCs.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  10. Input the DTC: P0560.

  11. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

Table 1. *a P/I-B *b EFI-MAIN *c Battery
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

Tip:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    INSPECT BATTERY


    1. Inspect the battery.

      Click here

      OK
      Battery is not depleted.
      Result
      Proceed to
      OK
      NG

  2. Click here

    CHECK BATTERY TERMINAL


    1. Check that the battery terminals are not loose or corroded.

      OK
      Battery terminals are not loose or corroded.
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE BATTERY TERMINAL

  3. *a Component with harness connected (ECM)
    Click here

    CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)


    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A77-5 (BATT) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ECM)

  4. Click here

    CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here


      1. Powertrain > Engine > Clear DTCs


    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG) and turn the GTS on.

    7. Wait 5 seconds or more.

    8. Enter the following menus: Powertrain / Engine / Trouble Codes.

    9. Read the DTCs.


      1. Powertrain > Engine > Trouble Codes


      Result
      Result Proceed to
      DTC P0560 is output A
      DTCs are not output B