Click here

SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P1023, P2614

Click here
Click here
DTC Code DTC Name
P1023 Camshaft Position Signal Output "B" Circuit
P2614 Camshaft Position Signal Output Circuit / Open
Click here

DESCRIPTION

Refer to DTC P0010.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1023 Camshaft Position Signal Output "B" Circuit Malfunction in rotation sensor of camshaft timing control motor is detected for 3 seconds (1 trip detection logic).

  • Camshaft timing control motor (bank 2)

  • ECM

 Comes on DTC stored
P2614 Camshaft Position Signal Output Circuit / Open Malfunction in rotation sensor of camshaft timing control motor is detected for 3 seconds (1 trip detection logic).

  • Camshaft timing control motor (bank 1)

  • ECM

 Comes on DTC stored
Table 1. Symptoms and Fail-safe Operation During Camshaft Control Motor Malfunction
Vehicle Condition Fail-Safe

  • Deterioration of driving performance as result of engine combustion degradation

  • Engine output deficiency

  • Power to camshaft timing control motor is cut

  • Valve timing of bank that is operating normally is fixed at maximum retard angle
Click here

MONITOR DESCRIPTION

This DTC is output when a malfunction in the intake side camshaft timing control motor's rotation sensor is detected. The camshaft timing control motor is equipped with a self diagnostic function, which is used to output the duty ratio (when normal: 70 to 90%) as a signal (VTM) to the ECM. If the ECM receives a duty signal of 40%, a DTC is output immediately (1 trip detection logic).

Click here

MONITOR STRATEGY

Required sensor/Components (Main) Camshaft timing control motor
Required sensor/Components (Related) -
Frequency of Operation Continuous
Click here

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

    Click here

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Start the engine.

  7. Idle the engine for 10 seconds or more.

  8. Enter the following menus: Powertrain / Engine / Trouble Codes.

  9. Read the pending DTC.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  11. Input the DTC: P1023 or P2614.

  12. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows NORMAL, the system is normal.

Click here

CAUTION / NOTICE / HINT

Tip:

  • Bank 1 refers to the bank that includes the No. 1 cylinder*.

    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

Click here

PROCEDURE


  1. Click here

    REPLACE CAMSHAFT TIMING CONTROL MOTOR (BANK 1 OR BANK 2)


    1. Replace the camshaft timing control motor.

      Click here

      Tip:

      Perform "Inspection After Repair" after replacing the camshaft timing control motor.

      Click here

      Result
      Proceed to
      NEXT

  2. Click here

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here


      1. Powertrain > Engine > Clear DTCs


    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG).

    7. Turn the GTS on.

    8. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    9. Enter the following menus: Powertrain / Engine / Trouble Codes.

    10. Read the DTCs.


      1. Powertrain > Engine > Trouble Codes


      Result
      Result Proceed to
      DTCs are not output A
      Other DTCs are output B