Click here

SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P1366, P1367

Click here
Click here Click here
DTC Code DTC Name
P1366 "E" Camshaft Position Actuator Circuit Open, Low, High Bank1
P1367 "E" Camshaft Position Actuator Circuit Open, Low, High Bank2
Click here

DESCRIPTION

Refer to DTC P0010.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1366 "E" Camshaft Position Actuator Circuit Open, Low, High Bank1 Malfunction in diagnostic signal (VTM) of camshaft timing control motor is detected for 3 seconds (1 trip detection logic).

  • Camshaft timing control motor (bank 1)

  • Open or short in camshaft timing control motor (bank 1) circuit

  • ECM

 Comes on DTC stored
P1367 "E" Camshaft Position Actuator Circuit Open, Low, High Bank2 Malfunction in diagnostic signal (VTM) of camshaft timing control motor is detected for 3 seconds (1 trip detection logic).

  • Camshaft timing control motor (bank 2)

  • Open or short in camshaft timing control motor (bank 2) circuit

  • ECM

 Comes on DTC stored
Click here

MONITOR DESCRIPTION

This DTC is output when a diagnostic signal malfunction is detected in the intake side camshaft timing control motor. The camshaft timing control motor is equipped with a self diagnostic function, which is used to output the condition of the camshaft timing control motor as a diagnosis signal (VTM) to the ECM. If the ECM receives a diagnosis signal that is not one of the set signals, a DTC is output immediately (1 trip detection logic).

Click here

MONITOR STRATEGY

Required sensors/Components (Main) Camshaft timing control motor
Required sensors/Components (Related) -
Frequency of Operation Continuous
Click here

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

    Click here

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Start the engine.

  7. Idle the engine for 10 seconds or more.

  8. Enter the following menus: Powertrain / Engine / Trouble Codes.

  9. Read the pending DTC.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  11. Input the DTC: P1366 or P1367.

  12. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows NORMAL, the system is normal.

Click here

WIRING DIAGRAM

Refer to DTC P1360.

Click here

Click here

CAUTION / NOTICE / HINT

Tip:

  • Bank 1 refers to the bank that includes the No. 1 cylinder.*

    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING CONTROL MOTOR - ECM)


    1. Disconnect the camshaft timing control motor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      F10-1 (VTM1) - F7-9 (EMD1) Always Below 1 Ω
      F35-1 (VTM2) - F2-31 (EMD2) Always Below 1 Ω
      F10-1 (VTM1) or F7-9 (EMD1) - Body ground Always 10 kΩ or higher
      F35-1 (VTM2) or F2-31 (EMD2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  2. Click here

    REPLACE CAMSHAFT TIMING CONTROL MOTOR (BANK 1 OR BANK 2)


    1. Replace the camshaft timing control motor.

      Click here

      Tip:

      Perform "Inspection After Repair" after replacing the camshaft timing control motor.

      Click here

      Result
      Proceed to
      NEXT

  3. Click here

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here


      1. Powertrain > Engine > Clear DTCs


    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Turn the engine switch on (IG) and turn the GTS on.

    7. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    8. Enter the following menus: Powertrain / Engine / Trouble Codes.

    9. Read the pending DTCs.


      1. Powertrain > Engine > Trouble Codes


      Result
      Result Proceed to
      DTCs are not output A
      Other DTCs are output B