REAR DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear door removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here


  • Door window regulator assembly

  • Door glass

  • Door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*1: When performing learning using the GTS. Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. B004PB3

      Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel plug.

  4. REMOVE REAR ARMREST ASSEMBLY


    1. B004R0HC01
      B004QOG Place Hand Here
      B004PI4 Remove in this Direction

      Disengage the 3 clips and 7 claws to remove the rear armrest assembly as shown in the illustration.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL


    1. B004P1YC01
      B004QOG Place Hand Here
      B004PI4 Remove in this Direction

      Disengage the 2 clips and 2 claws as shown in the illustration.

    2. Disconnect the connector to remove the rear power window regulator switch assembly with rear door upper armrest base panel.

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. B004PZLC01
      B004PFI Protective Tape

      Apply protective tape to the rear door panel as shown in the illustration.

    2. B004Q0O

      Remove the 3 screws.

    3. B004PWB

      Using a clip remover, disengage the 8 clips.

    4. B004Q86C01
      B004PI4 Remove in this Direction

      Pull out the rear door trim board sub-assembly as shown in the illustration to disengage the guide.

    5. Raise the rear door trim board sub-assembly to separate the rear door trim board sub-assembly with the rear door inner glass weatherstrip and No. 1 door scuff plate clamp.

    6. B004Q12C01
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly
      B004PI4 Remove in this Direction

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.

    7. B004QCU

      Using a screwdriver, disengage the claw to remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly.

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP WITH REAR DOOR NO. 2 VENT SEAL


    1. B004QDS

      Disengage the 5 claws to remove the rear door inner glass weatherstrip with rear door No. 2 vent seal.

  8. REMOVE REAR DOOR NO. 2 VENT SEAL


    1. B004P72C02
      B004PI4 Remove in this Direction

      Remove the rear door No. 2 vent seal from the rear door inner glass weatherstrip.

  9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. B004PKG

      Disengage the 2 claws to remove the rear door inside handle sub-assembly.

  10. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  11. REMOVE REAR DOOR FRAME GARNISH


    1. B004QKF

      Disengage the 2 claws to remove the rear door frame garnish.

  12. REMOVE REAR DOOR SERVICE HOLE COVER


    1. B004PZP

      Remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the rear door panel.

  13. REMOVE REAR DOOR PANEL PROTECTOR


    1. B004P9Z

      Remove the rear door panel protector.

  14. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER


    1. B004QKD

      Remove the rear door No. 2 service hole cover.

  15. REMOVE REAR DOOR GLASS RUN


    1. B004PHO

      Remove the rear door glass run.

  16. REMOVE REAR DOOR CHECK ASSEMBLY


    1. B004OGT

      Remove the 3 bolts and rear door check assembly.

  17. REMOVE REAR DOOR WEATHERSTRIP


    1. B004OT4C01
      *a Double-sided Tape

      Using a clip remover, disengage the 25 clips and remove the rear door weatherstrip.

  18. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. B004PR0C01
      B004PRK Screw
      B004P9H Bolt

      Remove the screw, 2 bolts and rear door window division bar sub-assembly.

  19. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. B004P0XC01
      B004PI4 Remove in this Direction

      Remove the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  20. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. B004OJ3

      Separate the rear door glass sub-assembly from the rear door window regulator assembly as shown in the illustration.

      Note

      After separating the rear door glass sub-assembly, do not allow it to fall.

    2. B004Q4FC01
      B004PI4 Remove in this Direction (1)
      B004OIV Remove in this Direction (2)

      Remove the rear door glass sub-assembly.

      Note

      Do not damage the rear door glass sub-assembly.

  21. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY


    1. B004OHTC01
      *a Protective Tape

      Using a screwdriver, remove the rear door glass channel sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  22. REMOVE REAR DOOR GLASS CHANNEL FILLER


    1. Remove the rear door glass channel filler from the rear door glass sub-assembly.

  23. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. Disconnect the connector.

    2. B004PM1C01
      *a Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

    3. Remove the 3 bolts and rear door window regulator assembly.

    4. Remove the temporary bolt from the rear door window regulator assembly.

  24. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

    Click here

  25. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. B004Q9G

      Disengage the 2 claws and move the lever as shown in the illustration.

    2. B004QGUC01
      B004PI4 Remove in this Direction

      Remove the rear door outside handle assembly as shown in the illustration.

  26. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    1. B004P87

      Using a T30 "TORX" socket wrench, loosen the screw.

      Tech Tips

      The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

    2. Disengage the claw to remove the rear door outside handle cover.

  27. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. B004P0Q

      Disengage the 3 claws to remove the rear door front outside handle pad.

  28. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. B004PYR

      Disengage the claw and 3 guides to remove the rear door rear outside handle pad.

  29. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. B004PO5C01
      *A Inside
      *B Outside

      Using a T30 "TORX" socket wrench, remove the screw.

    2. Slide the rear door outside handle frame sub-assembly to disengage the claw, and then remove it.

  30. REMOVE REAR DOOR PANEL CUSHION


    1. B004QLF

      Disengage the 2 claws to remove the rear door panel cushion.

  31. REMOVE REAR DOOR DUST PROOF SEAL


    1. B004Q92

      Disengage the 3 claws to remove the 3 rear door dust proof seals.

  32. REMOVE REAR DOOR NO. 3 WEATHERSTRIP


    1. B004QPVC01
      B004PFI Double-sided Tape

      Disengage the claw and remove the rear door No. 3 weatherstrip.

  33. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

    Click here

  34. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

    Click here

  35. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

    Click here

  36. REMOVE REAR DOOR REAR WINDOW FRAME MOULDING

    Click here

  37. REMOVE REAR DOOR LOWER OUTSIDE STRIPE (w/ Black Out Tape)

    Click here

  38. REMOVE REAR DOOR OUTSIDE STRIPE (w/ Black Out Tape)

    Click here

  39. REMOVE REAR DOOR UPPER OUTSIDE STRIPE (w/ Black Out Tape)

    Click here