ROOF HEADLINING REASSEMBLY

PROCEDURE


  1. INSTALL NO. 2 ROOF HEADLINING PAD (w/ Roof Headlining Pad)


    1. Align the No. 2 roof headlining pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

      A01RJDIC01
      *a Hot-melt Glue *b Marking

  2. INSTALL ROOF HEADLINING PAD (w/ Roof Headlining Pad)


    1. Align the roof headlining pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

      A01RJKSC01
      *a Hot-melt Glue *b Marking

  3. INSTALL NO. 1 ROOF WIRE


    1. Apply butyl tape as shown in the illustration.

      A01RJ60C02
      *A w/o Sliding Roof *B w/ Sliding Roof
      *a Marking - -
      B004PFI Butyl Tape - -

      Note

      Securely attach the butyl tape.

    2. Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining assembly.

      A01RLL7C01
      *A w/o Sliding Roof *B w/ Sliding Roof
      *C w/ Intrusion Sensor - -
      *a 90° - -
      B004PI4 Rotation Direction - -

    3. Engage each clamp.

    4. Align the marking tape (A) on the No. 1 roof wire with the tab on the front side of the roof headlining assembly.

      A01RHMXC01
      *A w/o Sliding Roof *B w/ Sliding Roof
      *C w/o Toyota Safety Sense *D w/ Toyota Safety Sense
      *E for LHD with Humidity Sensor or Rain Sensor *F for RHD with Humidity Sensor or Rain Sensor
      *G w/ EC Mirror - -
      *a Marking Tape (A) *b Marking Tape (B)
      *c Marking Tape (C) *d Marking
      *e Adjustment Area - -
      B004P9H Front - -

    5. Align the edge of each marking tape (B) on the No. 1 roof wire with each notch on the roof headlining assembly.

    6. w/ Sliding Roof:


      1. Align the edge of the marking tape (C) on the No. 1 roof wire with the marking on the roof headlining assembly.

    7. Attach the No. 1 roof wire with the butyl tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

      • Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    8. Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

      A01RHCGC01
      *A w/o Sliding Roof *B w/ Sliding Roof
      *C w/o Toyota Safety Sense *D w/ Toyota Safety Sense
      *E for LHD with Humidity Sensor or Rain Sensor *F for RHD with Humidity Sensor or Rain Sensor
      *G w/ EC Mirror *H w/ Intrusion Sensor
      *1 No. 1 Roof Wire - -
      *a Correct *b Incorrect
      *c 15 mm (0.591 in.) or more - -
      B004PFI Adhesive Tape - -

      Note


      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  4. INSTALL THEFT WARNING ULTRASONIC SENSOR (w/ Intrusion Sensor)

    Click here

  5. INSTALL VANITY LIGHT ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and LH side.


    1. A01RLV7C01
      *1 Bulb Holder
      *a Claw (A)
      *b Claw (B)

      Engage the claw (B) to install the vanity light assembly.

    2. Engage the 2 claws (A) to install the bulb holder to the vanity light assembly.

  6. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Click here

  7. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)


    1. Align the No. 2 roof silencer pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

      A01RL5MC02
      *a Hot-melt Glue *b Marking

  8. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)


    1. Align the No. 1 roof silencer pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

      A01RHWHC02
      *a Hot-melt Glue *b Marking