FRONT SEAT ASSEMBLY(for Power Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Power seat is available only on the driver side.

  • Use the same procedure for RHD and LHD vehicles.

  • The following procedure is for LHD vehicles.

PROCEDURE


  1. INSTALL POWER SEAT TILT MOTOR ASSEMBLY


    1. B004OZ1N01

      Install the power seat tilt motor assembly with the 3 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      Note

      Bolt (A) is shorter than bolt (B). Make sure to install them to the correct positions.

  2. INSTALL POWER SEAT LIFTER MOTOR ASSEMBLY


    1. Install the power seat lifter motor assembly.


      1. B004OL7C01
        *a Stud Bolt of the Front Seat Vertical Housing Sub-assembly
        *b Hole of the Front Seat Adjuster Assembly
        *c Front Seat Vertical Housing Sub-assembly
        *d Front Seat Adjuster Assembly

        Install the front seat vertical housing sub-assembly.

        Note


        • Make sure to insert the stud bolt of the front seat vertical housing sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.

        • Make sure to position the front seat adjuster assembly so that when the front seat vertical housing sub-assembly is installed, their gears will be positioned as shown in the illustration.

      2. B004OGX

        Install the vertical adjuster spacer.

      3. B004PQQN01

        Install the front seat adjuster plate with the 3 nuts.

        Torque:
        5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

        Note

        Tighten the nuts in the order shown in the illustration.

  3. INSTALL FRONT SEAT LOWER NO. 1 CUSHION SHIELD LH


    1. B004Q5JC01
      B004PI4 Install in this direction

      Engage the guide as shown in the illustration.

    2. B004PEO

      Engage the claw to install the front seat lower No. 1 cushion shield LH.

  4. INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER LH


    1. B004PEMC01
      B004PI4 Install in this direction

      Engage the guide as shown in the illustration.

    2. Engage the 2 claws to install the front seat cushion wire harness holder LH.

    3. B004QYL

      Install the 2 screws.

  5. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH


    1. B004Q8C

      Engage the 6 hooks to install the front seat cushion spring sub-assembly LH to the front seat adjuster assembly LH.

  6. INSTALL FRONT SEAT WIRE LH


    1. Connect each connector and engage each clamp to install the front seat wire LH.

  7. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH


    1. B004PIEC01
      *a Hook
      *b Guide

      Engage the claw and guide.

    2. Engage the hook to install the front seat lower cushion shield LH.

  8. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH


    1. B004POKC01
      *a Hook
      *b Guide

      Engage the claw and guide.

    2. Engage the hook to install the front seat lower cushion shield RH.

  9. INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH


    1. B004PTN

      Engage the 4 claws to install the LH seat reclining adjuster inside cover LH.

    2. B004PEW

      Engage the claw.

  10. INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH


    1. B004OPR

      Engage the 4 claws to install the LH seat reclining adjuster inside cover RH.

  11. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

    Click here

  12. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. B004QH3

      Engage the 13 claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.

  13. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. Engage the 10 hooks to install the separate type front seat cushion cover with pad.

      B004PVT
    2. B004OUC

      Engage the clamp to install the front seat cushion heater assembly LH wire harness.

    3. Connect the connector.

  14. INSTALL FRONT SEAT NO. 2 WIRE LH


    1. Connect each connector and engage each clamp to install the front seat No. 2 wire LH.

  15. INSTALL FRONT SEATBACK HOOK


    1. B004OSB

      Install the 2 front seatback hooks to the front seatback frame sub-assembly LH.

  16. INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. Install the 2 front seatback edge protectors to the lumbar support adjuster assembly LH.

  17. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Click here

  18. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  19. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH

    Click here

  20. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. B004PLV

      Engage the 17 claws to install the separate type front seatback cover to the separate type front seatback pad.

  21. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Install the separate type front seatback cover with pad.

  22. INSTALL FRONT SEAT HEADREST SUPPORT


    1. B004PXI

      Engage the 4 claws to install the 2 front seat headrest supports.

    2. B004OFGC01
      *1 Seat Cover Hanger
      *a Bracket
      B004PI4 Install in this direction

      Slide the bracket as shown in the illustration to engage the hook and connect the bracket to the seat cover hanger.

      Note


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after connecting the bracket to the seat cover hanger.

      • Install the bracket securely.

    3. B004QPFC01
      *1 Seatback Cover Hook
      *a Pin

      Insert the seatback cover hook and push in the pin to install it as shown in the illustration.

    4. B004OT6C01
      B004PI4 Install in this direction

      Engage the hook as shown in the illustration.

    5. B004QC7

      Close the 2 fasteners.

    6. B004OJ2

      Engage the clamp.

    7. B004P3A

      Engage the 3 hooks.

  23. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY


    1. B004QYB

      Engage the 4 guides.

    2. Install the separate type front seatback assembly to the separate type front seat cushion assembly with the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. B004OZR

      Engage the claw and 4 clamps to install the front seat airbag assembly LH wire harness.

      Tech Tips

      Engage the claw first.

    4. B004Q24

      Engage the clamp.

    5. Connect the front seatback heater assembly LH connector.

    6. B004Q5M

      Engage the clamp.

    7. Connect the connector.

    8. B004PD4

      Engage the 2 hooks.

    9. B004Q5F

      Pass the separate type front seatback cover through the grooves of the LH seat reclining adjuster inside cover LH and LH seat reclining adjuster inside cover RH.

  24. INSTALL FRONT POWER SEAT SWITCH LH

    Click here

  25. INSTALL FRONT SEAT SIDE NO. 1 BRACKET LH


    1. B004Q6U

      Install the front seat side No. 1 bracket LH to the front seat cushion shield LH with the 2 screws.

  26. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. B004PAH

      Engage the 4 claws to install the reclining power seat switch knob.

  27. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. B004PAR

      Engage the 4 claws to install the slide and vertical power seat switch knob.

  28. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. B004P8XC01
      B004PI4 Install in this direction

      Engage the 2 claws and 2 guides as shown in the illustration.

    2. B004Q1M

      Engage the 2 claws to install the front seat inner cushion shield LH.

  29. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. B004OWR

      Connect the front power seat switch LH connector.

    2. B004PX0C01
      B004PI4 Install in this direction (1)
      B004OIV Install in this direction (2)

      Engage the guide (A) as shown in the illustration.

    3. Engage the 2 claws and 2 guides (B) as shown in the illustration.

    4. B004OVI

      Engage the 2 claws to install the front seat cushion shield LH.

  30. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH


    1. B004OLS

      Engage the 3 guides.

    2. B004PGW

      Engage the 2 claws as shown in the illustration.

    3. B004QS4

      Engage the guide as shown in the illustration.

    4. B004PER

      Install the front seat inner No. 1 cushion shield LH with the clip.

  31. CONNECT SEPARATE TYPE FRONT SEATBACK COVER


    1. B004PE2

      Connect the rubber band of the separate type front seatback cover.

  32. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    Click here