FRONT SEAT ASSEMBLY(for Manual Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The following procedure is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY


    1. B004Q52

      Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the front seat airbag assembly connector under the front seat assembly.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B004Q53C01
        *a Correct *b Incorrect
        *c Yellow CPA - -

      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • When connecting any airbag connector, take care not to damage the airbag wire harness.


        • When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.

    3. Connect each connector and engage each clamp under the front seat assembly.

    4. Temporarily install the front seat assembly with the 4 bolts.

    5. Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.

    6. B004OPNN01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

    7. Operate the seat track adjusting handle and move the front seat assembly to the foremost position.

    8. B004PMEN01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

  2. INSPECT SEAT SLIDE ADJUSTER LOCK


    1. While performing a sliding operation of the front seat assembly, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the front seat assembly installation bolts and adjust the adjuster position.

  3. INSTALL INNER SEAT TRACK BRACKET COVER


    1. Operate the seat track adjusting handle and move the front seat assembly to the foremost position.

    2. B004P99

      Engage the 2 claws and guide to install the inner seat track bracket cover.

  4. INSTALL OUTER SEAT TRACK COVER


    1. B004ON2

      Engage the 2 claws and guide to install the outer seat track cover.

  5. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    1. Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.

    2. B004P5E

      Engage the 2 claws to install the front inner seat track bracket cover.

  6. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER


    1. B004P27

      Engage the 2 claws to install the front outer seat track bracket cover.

  7. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly to the front seat assembly.

  8. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Click here

  9. CHECK SEAT HEATER (w/ Seat Heater System)

    Click here

  10. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  11. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Side)


    1. w/ Occupant Classification System:

      Click here