PRE-CRASH SAFETY SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Pre-Crash 2
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Turn Light RH Turn signal switch (right) status ON or OFF

      ON: Turn signal switch (right) on

      OFF: Turn signal switch (right) off

      		 -
      Turn Light LH Turn signal switch (left) status ON or OFF

      ON: Turn signal switch (left) on

      OFF: Turn signal switch (left) off

      		 -
      PCS OFF Switch Pre-crash safety system on/off status ON or OFF

      ON: Pre-crash safety system on

      OFF: Pre-crash safety system off

      		 -
      Pre-Crash Safety Warning Buz Pre-crash safety system warning buzzer Valid or Inval

      Valid: Pre-crash safety system warning buzzer operation possible

      Inval: Pre-crash safety system warning buzzer operation not possible

      		 -
      Pre-Crash Brake Pre-crash braking function Valid or Inval

      Valid: Pre-crash braking operation possible

      Inval: Pre-crash braking operation not possible

      		 -
      PBA Start Pre-crash brake assist activation signal OFF, Standby, Assist Lv1 or Assist Lv2

      OFF: Pre-crash brake assist not operating

      Standby: Brake pedal not depressed during pre-crash brake assist operation

      Assist Lv1: Brake pedal depressed during pre-crash brake assist operation

      Assist Lv2: Brake pedal firmly depressed during pre-crash brake assist operation

      		 Signal status changes when the pre-crash brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal)
      Warning Brake - - - Not applicable to the vehicle
      Brake Assist Standby - - - This item is displayed on the GTS but is not used.
      Pre-Crash Brake Control Pre-crash braking operational status ON or OFF

      ON: Pre-crash braking operating

      OFF: Pre-crash braking not operating

      		 -
      AVS Start - - - Not applicable to the vehicle
      VGRS Start - - - Not applicable to the vehicle
      PBA Control Pre-crash brake assist operational status Valid or Invalid

      Valid: Pre-crash brake assist control operation possible

      Invalid: Pre-crash brake assist control operation not possible

      		 -
      Pre-Crash Safety Brake Ind Pre-crash safety system alarm warning message status ON or OFF

      ON: Displayed

      OFF: Not displayed

      		 "BRAKE!" is displayed
      PCS Crash Alarm Buzzer Skid control buzzer status ON or OFF

      ON: Skid control buzzer sounding

      OFF: Skid control buzzer not sounding

      		 -
      Front Radar-Low Voltage History Millimeter wave radar sensor assembly low voltage history ON or OFF

      ON: History of low voltage

      OFF: No history of low voltage

      		 -
      Front Radar-Incorrect Axial Gap (Vertical) History Millimeter wave radar sensor assembly vertical misalignment history ON or OFF

      ON: History of vertical misalignment

      OFF: No history of vertical misalignment

      		 -
      Front Radar-Incorrect Axial Gap (Horizontal) History Millimeter wave radar sensor assembly horizontal misalignment history ON or OFF

      ON: History of horizontal misalignment

      OFF: No history of horizontal misalignment

      		 -
      Front Recognition Camera-Malfunction History Forward recognition camera system unavailable history ON or OFF

      ON: History of unavailable

      OFF: No history of unavailable

      		 -
      Control Mode ECU control mode status Normal or Check

      Normal: Normal operation

      Check: Operating in Control Mode

      		 -
      PCS Operation State Retention Setting PCS Operation State Retention Setting customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 1 PCS Alarm Activation Distance Retention Setting 1 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 2 PCS Alarm Activation Distance Retention Setting 2 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -
      PCS Alarm Activation Distance Retention Setting 3 PCS Alarm Activation Distance Retention Setting 3 customize setting ON or OFF

      ON: Customize setting set to ON

      OFF: Customize setting set to OFF

      		 -

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    7. Read the Data List according to the display on the GTS.


      Chassis > ABS/VSC/TRC > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch assembly ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      Stop Light Relay Output

      Stop light control relay (Stop light switch assembly)

      (STPO terminal output)

      		 ON or OFF

      ON: Relay output on

      OFF: Relay output off

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Pre-Crash 2 > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      PCS Crash Alarm Buzzer Skid control buzzer ON / OFF Test possible with power switch on (IG), vehicle stopped

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    7. Perform the Active Test according to the display on the GTS.


      Chassis > ABS/VSC/TRC > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Stop Light Relay Stop light control relay (Stop light switch assembly) ON / OFF Test possible at vehicle speed of 0 km/h (0 mph)

    8. Enter the following menus: Body Electrical / Combination Meter / Active Test.

    9. Perform the Active Test according to the display on the GTS.


      Body Electrical > Combination Meter > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Indicat. Precrash PCS warning light ON / OFF Test possible with power switch on (IG), vehicle stopped