FRONT PASSENGER AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the instrument panel passenger airbag assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system
Simple intelligent parking assist system
Pre-crash safety system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B004R04

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE GLOVE BOX LIGHT ASSEMBLY

    Click here

  3. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      B004PKN
    3. B004PUCC01
      *a Slider

      w/o Passenger Airbag ON/OFF Indicator:


      1. Slide the slider to release the lock, and then disconnect the connector.

        Note

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    4. B004OI6C01
      *a Slider

      w/ Passenger Airbag ON/OFF Indicator:


      1. Slide the slider to release the lock, and then disconnect the connector.

        Note

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  4. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

  5. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

    CAUTION:

    When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.

    B004Q46C02
    B004PFI Deployment Side

    1. w/o Passenger Airbag ON/OFF Indicator:


      1. B004Q1I

        Remove the 2 screws.

      2. B004P89C01
        *a Passenger Airbag Door Retainer

        Using a screwdriver, pry back the passenger airbag door retainer to disengage the 3 hooks as shown in the illustration.

        Note

        Do not damage the deployment surface of the instrument panel passenger airbag assembly.

      3. B004QXT

        Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the lower instrument panel sub-assembly.

    2. w/ Passenger Airbag ON/OFF Indicator:


      1. B004QP7

        Remove the 2 screws.

      2. B004OVBC01
        *a Passenger Airbag Door Retainer

        Using a screwdriver, pry back the passenger airbag door retainer to disengage the 3 hooks as shown in the illustration.

        Note

        Do not damage the deployment surface of the instrument panel passenger airbag assembly.

      3. B004Q57

        Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the lower instrument panel sub-assembly.

  6. REMOVE NO. 2 INSTRUMENT PANEL WIRE


    1. w/o Passenger Airbag ON/OFF Indicator:


      1. B004PLLC01
        *a Protective Tape
        *b Airbag Connector
        *c Airbag Connector Lock

        Disengage the clamp.

      2. Using a screwdriver with its tip wrapped with protective tape, release the airbag connector lock.

      3. Disconnect the airbag connector to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.

        Note

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    2. w/ Passenger Airbag ON/OFF Indicator:


      1. B004QVKC01
        *a Protective Tape
        *b Airbag Connector
        *c Airbag Connector Lock

        Disengage the clamp.

      2. Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locks.

      3. Disconnect the 2 airbag connectors to remove the No. 2 instrument panel wire from the instrument panel passenger airbag assembly.

        Note

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.