LIGHTING SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      ACC SW Power switch on (ACC) signal ON or OFF

      ON: Power switch on (ACC)

      OFF: Power switch off

      		 -
      IG SW Power switch on (IG) signal ON or OFF

      ON: Power switch on (IG)

      OFF: Power switch off

      		 -
      RR Door Courtesy SW Rear door courtesy light switch assembly RH signal ON or OFF

      ON: Rear door RH open

      OFF: Rear door RH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch assembly LH signal ON or OFF

      ON: Rear door LH open

      OFF: Rear door LH closed

      		 -
      Back Door Courtesy SW Back Door Courtesy SW ON or OFF

      ON: Back door open

      OFF: Back door closed

      		 -
      FR Door Lock Pos Front door RH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door RH locked

      UNLOCK: Front door RH unlocked

      		 -
      FR Door Courtesy SW Front door courtesy light switch assembly RH signal ON or OFF

      ON: Front door RH open

      OFF: Front door RH closed

      		 -
      FL Door Lock Pos Front door LH unlock detection switch signal LOCK or UNLOCK

      LOCK: Front door LH locked

      UNLOCK: Front door LH unlocked

      		 -
      FL Door Courtesy SW Front door courtesy light switch assembly LH signal ON or OFF

      ON: Front door LH open

      OFF: Front door LH closed

      		 -
      RR-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF

      ON: Rear door RH or LH unlocked

      OFF: Rear door RH and LH locked

      		 -
      RL-Door Lock Pos SW Rear door RH and LH unlock detection switch signal ON or OFF

      ON: Rear door RH or LH unlocked

      OFF: Rear door RH and LH locked

      		 -
      Interior Light Control Operation of the illuminated entry system ON or OFF Customized value is displayed -
      I/L ON W/Door Key Unlock Function that lights up the interior lights when the doors are unlocked ON or OFF Customized value is displayed -
      Lighting Time Lighting time of the delay control function (illuminated entry system) 15s, 7.5s or 30s Customized value is displayed -
      Room Light when Aprchd Function that lights up the interior lights when a key enters any actuation area ON or OFF Customized value is displayed -
      Inside Foot Light Function that lights up the footwell light* ON or OFF Customized value is displayed -
      I/L when ACC OFF Function that lights up the interior lights when the power switch is turned from on (ACC or IG) to off ON or OFF Customized value is displayed -
      Light Control Function that lights up the footwell light* ON or OFF Customized value is displayed -

      • *: w/ Footwell Light

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / (desired system) / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Illuminated Entry System Turns on the lights that are controlled by the illuminated entry system.*1 ON or OFF Perform the Active Test with door switch in the map light assembly turned on.
      Fr Foot Light Footwell light*2 ON or OFF -
      Relay for Interior Light Auto Cut Function DOME CUT relay ON or OFF

      When performing this Active Test, turn all the interior lights on.


      • ON: DOME CUT relay off (interior lights turn off)

      • OFF: DOME CUT relay on (interior lights turn on)

      • *1: Refer to System Description for the lights that are controlled by the illuminated entry system.

        Click here

      • *2: w/ Footwell Light


      Body Electrical > Entry&Start > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Power/Engine SW Light Power switch illumination ON or OFF -