REAR DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here


  • Rear door glass sub-assembly

  • Rear door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE REAR ARMREST ASSEMBLY

    Click here

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

    Click here

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP WITH REAR DOOR NO. 2 VENT SEAL

    Click here

  8. REMOVE REAR DOOR SERVICE HOLE COVER

    Click here

  9. REMOVE REAR DOOR PANEL PROTECTOR

    Click here

  10. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

    Click here

  11. REMOVE REAR DOOR GLASS RUN

    Click here

  12. DISCONNECT REAR DOOR WEATHERSTRIP


    1. Disconnect the rear door weatherstrip until the screw of the rear door window division bar sub-assembly is visible.

  13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

    Click here

  14. REMOVE REAR DOOR QUARTER WINDOW GLASS

    Click here

  15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

    Click here

  16. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY


    1. B004PAWC01
      *a Release Plate
      B004PI4 Remove in this Direction

      Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the 3 screws.

    3. Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.

    4. When reusing the rear door lock with motor assembly:


      1. B004QZ1

        Remove the door lock wiring harness seal from the rear door lock with motor assembly.

  17. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)


    1. B004PRL

      Using a screwdriver, disengage the 2 claws to open the cover as shown in the illustration.

    2. B004QG2C01
      B004PI4 Remove in this Direction

      Remove the rear door lock remote control cable assembly as shown in the illustration.

  18. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)


    1. B004QZZ

      Using a screwdriver, disengage the 4 claws to open the cover as shown in the illustration.

    2. B004Q5OC01
      B004PI4 Remove in this Direction

      Remove the rear door inside locking cable assembly as shown in the illustration.

  19. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)


    1. B004QIO

      Using a screwdriver, disengage the 2 claws to open the cover as shown in the illustration.

    2. B004PCRC01
      B004PI4 Remove in this Direction

      Remove the rear door lock remote control cable assembly as shown in the illustration.

  20. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)


    1. B004OG6

      Using a screwdriver, disengage the 5 claws to open the cover as shown in the illustration.

    2. B004QCPC01
      B004PI4 Remove in this Direction

      Remove the rear door inside locking cable assembly as shown in the illustration.