DOOR CONTROL RECEIVER REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during electrical key and tire pressure warning ECU and receiver removal/installation are shown below.

Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Electrical key and tire pressure warning ECU and receiver

  • Register transmitter ID

  • Initialize tire pressure warning system

  • When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

  • Tire pressure warning function

Click here for Registration

Click here for Initialization

Note

When replacing the electrical key and tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

Click here

PROCEDURE


  1. REMOVE TONNEAU COVER ASSEMBLY

    Click here

  2. REMOVE REAR NO. 1 FLOOR BOARD

    Click here

  3. REMOVE DECK BOARD RETAINER

    Click here

  4. REMOVE DECK FLOOR BOX LH (w/o Spare Tire)

    Click here

  5. REMOVE REAR DECK FLOOR BOX (w/ Compact Spare Tire)

    Click here

  6. REMOVE DECK FLOOR BOX LH (w/ Compact Spare Tire)

    Click here

  7. REMOVE DECK FLOOR BOX RH (w/ Full Size Spare Tire)

    Click here

  8. REMOVE DECK FLOOR BOX LH (w/ Full Size Spare Tire)

    Click here

  9. REMOVE DECK TRIM SERVICE HOLE COVER

    Click here

  10. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side)

    Click here

  11. REMOVE REAR DECK TRIM COVER

    Click here

  12. REMOVE REAR SEAT HEADREST ASSEMBLY

    Click here

  13. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

    Click here

  14. REMOVE REAR SEATBACK ASSEMBLY LH

    Click here

  15. REMOVE REAR SEAT CUSHION ASSEMBLY

    Click here

  16. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  17. REMOVE REAR DOOR SCUFF PLATE LH

    Click here

  18. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  19. REMOVE REAR UNDER SIDE COVER LH

    Click here

  20. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH

    Click here

  21. REMOVE REAR SEAT SIDE GARNISH LH

    Click here

  22. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)

    Click here

  23. REMOVE NO. 1 TONNEAU COVER HOLDER CAP

    Click here

  24. REMOVE TONNEAU COVER HOOK A

    Click here

  25. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  26. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    Click here

  27. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH

    Click here

  28. REMOVE SMART DOOR CONTROL RECEIVER ASSEMBLY (w/o Tire Pressure Warning System)

    Note


    • Do not drop, strike or otherwise subject the smart door control receiver assembly to impact.

    • If the smart door control receiver assembly is subjected to an impact, replace it with a new one.


    1. A01RHI4

      Remove the bolt.

    2. Disengage the 2 guides.

    3. Disconnect the connector to remove the smart door control receiver assembly.

  29. REMOVE ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)

    Note


    • Do not drop, strike or otherwise subject the electrical key and tire pressure warning ECU and receiver to impact.

    • If the electrical key and tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.


    1. A01RKPE

      Remove the bolt.

    2. Disengage the 2 guides.

    3. Disconnect the connector to remove the electrical key and tire pressure warning ECU and receiver.