LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2321

DTC Code DTC Name
B2321 Driver Side Door ECU Communication Stop

DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2321 Driver Side Door ECU Communication Stop No communication between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Power window regulator motor assembly (for driver door)

  • Main body ECU (multiplex network body ECU)

  • Multiplex network master switch assembly

  • Wire harness or connector

  • POWER fuse

WIRING DIAGRAM

B004QEBE01

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.


      Body Electrical > Main Body > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Check for DTCs.


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      B1206 and B2321 are output simultaneously A
      Only B2321 is output B

    A

    GO TO DTC B1206 Click here

    B

  3. INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


    1. B004PSSC08
      *a

      Component without harness connected

      (Multiplex Network Master Switch Assembly)

      Remove the multiplex network master switch assembly.

      Tech Tips

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J7-16 (LIN2) - J7-17 (LIN1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY Click here

    OK

  4. CONFIRM MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for LHD A
      for RHD B

    B

    CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)) Click here

    A

  5. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))


    1. Disconnect the J2 power window regulator motor assembly (for driver door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Note

      Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J7-16 (LIN2) - J2-9 (LIN) Power Switch off Below 1 Ω
      J7-16 (LIN2) or J2-9 (LIN) - Body ground Power Switch off 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - AUXILIARY BATTERY, BODY GROUND)


    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J2-2 (B) - J2-1 (GND) Power Switch off 11 to 14 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J2-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


    1. Replace the power window regulator motor assembly (for driver door).

      Tech Tips

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  8. CLEAR DTC


    1. Clear the DTCs.


      Body Electrical > Main Body > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  9. CHECK FOR DTC


    1. Check for DTCs.


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      B2321 is not output A
      B2321 is output B

    A

    END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) WAS DEFECTIVE)

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

  10. CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))


    1. Disconnect the I2 power window regulator motor assembly (for driver door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Note

      Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the power switch from on (IG) to off and wait for 180 seconds or more without operating any switches.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J7-16 (LIN2) - I2-9 (LIN) Power Switch off Below 1 Ω
      J7-16 (LIN2) or I2-9 (LIN) - Body ground Power Switch off 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) - AUXILIARY BATTERY, BODY GROUND)


    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I2-2 (B) - I2-1 (GND) Power Switch off 11 to 14 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I2-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)


    1. Replace the power window regulator motor assembly (for driver door).

      Tech Tips

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  13. CLEAR DTC


    1. Clear the DTCs.


      Body Electrical > Main Body > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  14. CHECK FOR DTC


    1. Check for DTCs.


      Body Electrical > Main Body > Trouble Codes
      Result
      Result Proceed to
      B2321 is not output A
      B2321 is output B

    A

    END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door) WAS DEFECTIVE)

    B

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here