WINDSHIELD OUTSIDE MOULDING REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during windshield outside moulding removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Windshield glass sub-assembly Adjust forward recognition camera

  • Dynamic radar cruise control system

  • Lane departure alert system (w/ Steering Control)

  • Pre-crash safety system

  • Forward recognition camera system

  • Automatic high beam system

Click here

Note

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.

PROCEDURE


  1. REMOVE WINDSHIELD OUTSIDE MOULDING


    1. A003PKPC01
      B004PFI Protective Tape

      Apply protective tape around the windshield outside moulding.

    2. A003PQH

      Using a moulding remover, disengage the 2 claws.

    3. A003PP5C01
      B004PI4 Remove in this Direction

      Using a screwdriver, disengage the 10 claws as shown in the illustration.

    4. A003PPT

      Disengage the guide and remove the windshield outside moulding.

  2. REMOVE NO. 2 WINDSHIELD OUTSIDE MOULDING CLIP

    Tech Tips

    Perform the following procedure only when replacement of a No. 2 windshield outside moulding clip is necessary.


    1. A003PI4C01
      B004PI4 Remove in this Direction

      Disengage the clip as shown in the illustration to remove the No. 2 windshield outside moulding clip.

  3. REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

    Tech Tips

    Perform the following procedure only when replacement of a No. 1 windshield outside moulding clip is necessary.


    1. A003PSEC01
      B004PI4 Remove in this Direction

      Disengage the 5 claws as shown in the illustration to remove the 5 No. 1 windshield outside moulding clips.

  4. REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

    Tech Tips

    Perform the following procedure only when replacement of a No. 3 windshield outside moulding clip is necessary.


    1. Remove the windshield glass sub-assembly.

      Click here

    2. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    3. A003PP7C05
      *a Tape

      Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Standard Measurement
      Area Measurement
      A 5.0 mm (0.197 in.)

      Note

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    4. A003PBLC01
      *a Flange

      Lightly press the drill bit against the No. 3 windshield outside moulding clips to drill off the No. 3 windshield outside moulding clip flanges, and remove the 5 No. 3 windshield outside moulding clips.

      CAUTION:

      Be careful of the drilled No. 3 windshield outside moulding clips, as they may be hot.

      Note


      • Make sure to protect both the inside and outside of the vehicle as the No. 3 windshield outside moulding clip shavings will fly about.

      • Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

      • Prying the No. 3 windshield outside moulding clip with the drill may damage the No. 3 windshield outside moulding clip installation hole or drill bit.

    5. Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.