VEHICLE PROXIMITY NOTIFICATION SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

    6. Read the Data List according to the display on the GTS.


      Body Electrical > Vehicle Proximity Notification System > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light SW Stop light switch signal OFF or ON

      OFF: Brake pedal released

      ON: Brake pedal depressed

      		 -
      Operation Cancel SW Pattern select switch assembly (vehicle approaching speaker switch) signal OFF or ON

      OFF: Pattern select switch assembly (vehicle approaching speaker switch) is not pressed.

      ON: Pattern select switch assembly (vehicle approaching speaker switch) is pressed.

      		 -
      IG2 IG signal OFF or ON

      OFF: Power switch off

      ON: Power switch on (IG)

      		 -
      Ready Signal Ready signal OFF or ON

      OFF: Power switch off

      ON: Power switch on (Ready)

      		 -
      Dimming Request Status of Proximity Sound Indicator Illumination dimming status of the indicator light Indeterminacy / Non-dimming / Dimming

      Indeterminacy: No automatic light control sensor signal

      Non-dimming: Automatic light control sensor daytime signal

      Dimming: Automatic light control sensor nighttime signal

      		 -
      Engine Mode Status of the engine Stopped / Move to Stopping / Starting / Running Displays current engine status -
      Shift Switch Status Shift position signal P Range / R Range / N Range / D Range / B Range Displays current shift status -
      HV Motor Rotational Speed RPM of the HV motor -10000 to 10000 [rpm] Displays current HV motor RPM -
      Vehicle Speed Vehicle speed signal -327.68 to 327.67 [km/h] Displays current vehicle speed -
      Vehicle Speed Signal Status Whether the Vehicle speed is within the vehicle proximity notification system operation range. Available / Not Available

      Available: Vehicle speed within operation range

      Not Available: Vehicle speed not within operation range

      		 -
      AD Voltage of Speaker Abnormal Open or short in speaker circuit 0 to 5 [V]

      0 V: Open

      5 V: Short

      		 -
      Voltage of Amplifier Circuit Input voltage 0 to 20 [V] Current input voltage -
      Proximity Sound Volume Adjustment Warning sound volume setting Standard, Standard +1, Standard +2 Customized value displayed -
      Proximity Sound Level Increase (Vehicle Starting) Warning sound amplifier function when vehicle starts off OFF or ON Customized value displayed -
      Proximity Sound Control (Vehicle Stationary) Warning sound setting function when vehicle stopped OFF or ON Customized value displayed -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.

    6. Perform the Active Test according to the display on the GTS.


      Body Electrical > Vehicle Proximity Notification System > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Proximity Sound Indicator Proximity sound indicator OFF or ON -
      Proximity Sound (Vehicle Stationary) Proximity sound (Vehicle stationary) OFF or ON Produces warning sound when vehicle is stopped
      Proximity Sound (Low Speed) Proximity sound (Low speed) OFF or ON Produces warning sound when vehicle is being driven at speeds of 10 km/h (6 mph)